Content for  TS 27.007  Word version:  19.0.0

Set command enables reporting upon change in battery connection status, with unsolicited result code +CBCON: <bcs>. Read command returns the status of result code presentation and the current battery status. Test command returns values supported as a compound value.

<reporting> <bcs>

Optional.

Set command enables reporting upon change in battery charger status, with unsolicited result code +CBCHG: <chg_status>. Read command returns the status of result code presentation and the current battery charger status. Test command returns values supported as a compound value.

<reporting> <chg_status>

Optional.

Set command decides what format to print IPV6 address parameters of other AT commands. See RFC 4291 for details of the IPv6 address format. The +CGPIAF parameters <IPv6_AddressFormat>, <IPv6_SubnetNotation>, <IPv6_LeadingZeros> and <IPv6_CompressedZeros> affect the following commands and parameters:

1. in +CGTFT and +CGTFTRDP, the <remote address and subnet mask>;
2. in +CGDCONT, the <PDP_addr>;
3. in +CGPADDR, the <PDP_addr_1> and <PDP_addr_2>;
4. in +CGCONTRDP, the <local address and subnet mask>, <DNS_prim_addr>, <DNS_sec_addr>, <P_CSCF_prim_addr> and <P_CSCF_sec_addr>; and
5. in +CRC, the <PDP_addr> of unsolicited result code +CRING: GPRS <PDP_type>, <PDP_addr>[, [<L2P>][,<APN>]].

Read command returns the current command parameter settings. Test command returns values supported as compound values.

<IPv6_AddressFormat> <IPv6_SubnetNotation> <IPv6_LeadingZeros> <IPv6_CompressZeros>

Optional.

SRVCC provides the ability to have a seamless handover of a voice call between the PS domain and the CS domain for calls that are anchored in IMS, when the UE is capable of transmitting/receiving on only one of those access networks (PS or CS) at a given time, see clause 7.2a of TS 23.221, Annex A.1 and Annex A.2. The SRVCC support also includes the support of 5G-SRVCC from NG-RAN to UTRAN as specified in clause 6.5.4 of TS 23.216. Set command informs MT about the SRVCC Support. MT normally updates the network when changing this parameter. Refer to clause 9.2 for possible <err> values. Read command returns the status of the MT stored SRVCC Support. Test command returns supported values as a compound value.

<uesrvcc>: integer type. SRVCC support status 0 (default) 1

Optional.

Set command enables or disables reporting of PS to CS Single Radio Voice Call Continuity (SRVCC), PS to CS Single Radio Video Call Continuity (vSRVCC) handover information and CS to PS Single Radio Voice Call Continuity (see TS 24.237), of IMS Voice Over PS sessions (IMSVOPS) indicator information and of IMS Voice Over PS sessions over non-3GPP (IMSVOPS-N3GPP) indicator information, by the following unsolicited result codes: Read command returns the status of result code presentation and the IMSVOPS supported indication. Test command returns supported values as a compound value.

<reporting> <nwimsvops> <nwimsvops_n3gpp> <srvcch>

Optional.

Execution command cause the MT to return the number of remaining PIN retries for the MT passwords with intermediate result code +CPINR: <code>,<retries>[,<default_retries>] for standard PINs and +CPINRE: <ext_code>,<retries>[,<default_retries>] for manufacturer specific PINs. One line with one intermediate result code is returned for every <code> or <ext_code> selected by <sel_code>. When execution command is issued without the optional parameter <sel_code>, intermediate result codes are returned for all <code>s and <ext_code>s. In the intermediate result codes, the parameter <default_retries> is an optional (manufacturer specific) parameter, per <code> and <ext_code>. Refer to clause 9.2 for possible <err> values.

<retries> <default_retries> <code> <ext_code> <sel_code>

Optional.

When a MT is equipped with multiple card slots, the set command directs the MT to select the SIM/UICC card installed in the indicated card slot in all future actions that require the use of SIM/UICC. If this command is issued when a SIM/UICC is active, +CME ERROR is returned. Refer to clause 9.2 for possible <err> values. Read command returns the currently selected card slot. Test command returns the number of card slots in the MT as a compound value. The numbering of card slots is implementation dependent.

<card slot>

Optional.

This command allows for reading and dynamical reporting of local emergency numbers and categories or emergency service URNs as received from the network in the Emergency Number List IE (see TS 24.008) and the Extended Emergency Number List IE (see TS 24.301. The emergency numbers are not necessarily received for the same <mcc> and <mnc> as currently registered to. Read command returns one line of intermediate result code +CEN1: <reporting>,<mcc>,<mnc> with the current <reporting> setting and the Mobile Country Code <mcc> and Mobile Network Code <mnc>. Then follows zero or more occurrences of the local emergency number received in the Emergency Number List IE with intermediate result code +CEN2: <cat>,<number>. This is followed by one line of intermediate result code +CEN3: <validity> with the current <validity> setting. This is followed by zero or more occurrences of the local emergency number received in the Extended Emergency Number List IE and an associated sub-service with intermediate result code +CEN4: <number-ext>,<sub-service>. Set command enables reporting of local emergency numbers received from the network with unsolicited result codes equal to the intermediate result codes of the read form of the command. Test command returns values supported as a compound value.

<reporting> <mcc> <mnc> <cat> <number> <validity> <number-ext> <sub-service>

Optional.

Set command informs the MT whether the UE is currently available for voice calls with the IMS (see TS 24.229). The information can be used by the MT to determine "IMS voice not available" as defined in TS 24.301 and TS 24.501, and for mobility management for IMS voice termination, see TS 24.008. Read command returns the UEs IMS voice call availability status stored in the MT. Test command returns supported values as a compound value.

<state>

Optional.

Execution command returns received signal quality parameters. If the current serving cell is not a GERAN cell, <rxlev> and <ber> are set to value 99. If the current serving cell is not a UTRA FDD or UTRA TDD cell, <rscp> is set to 255. If the current serving cell is not a UTRA FDD cell, <ecno> is set to 255. If the current serving cell is not an E-UTRA cell, <rsrq> and <rsrp> are set to 255. If the current serving cell is not an NR cell, <ss_rsrq>, <ss_rsrp> and <ss_sinr> are set to 255. Refer to clause 9.2 for possible <err> values. Test command returns values supported as compound values.

<rxlev> <ber> <rscp> <ecno> <rsrq> <rsrp> <ss_rsrq> <ss_rsrp> <ss_sinr>

Optional.