Tech-invite3GPPspaceIETFspace
96959493929190898887868584838281807978777675747372717069686766656463626160595857565554535251504948474645444342414039383736353433323130292827262524232221201918171615141312111009080706050403020100
in Index   Prev   Next

RFC 2896

Remote Network Monitoring MIB Protocol Identifier Macros

Pages: 84
Informational
Part 2 of 4 – Pages 5 to 44
First   Prev   Next

Top   ToC   RFC2896 - Page 5   prevText

3.1.1. The TCP/IP protocol stack

arp PROTOCOL-IDENTIFIER PARAMETERS { } ATTRIBUTES { } DESCRIPTION "An Address Resolution Protocol message (request or response). This protocol does not include Reverse ARP (RARP) packets, which are counted separately." REFERENCE "RFC 826 [RFC826] defines the Address Resolution Protocol."
Top   ToC   RFC2896 - Page 6
    ::= {
     ether2 0x806,   -- [ 0.0.8.6 ]
     snap   0x806,
     802-1Q 0x806    -- [ 0.0.8.6 ]
    }

ip PROTOCOL-IDENTIFIER
    PARAMETERS {
       countsFragments(0)  -- This parameter applies to all child
                           -- protocols.
    }
    ATTRIBUTES {
     hasChildren(0),
     addressRecognitionCapable(1)
    }
    DESCRIPTION
       "The protocol identifiers for the Internet Protocol (IP). Note
       that IP may be encapsulated within itself, so more than one of
       the following identifiers may be present in a particular
       protocolDirID string."
    CHILDREN
       "Children of 'ip' are selected by the value in the Protocol field
       (one octet), as defined in the PROTOCOL NUMBERS table within the
       Assigned Numbers Document.

       The value of the Protocol field is encoded in an octet string as
       [ 0.0.0.a ], where 'a' is the protocol field .

       Children of 'ip' are encoded as [ 0.0.0.a ], and named as 'ip a'
       where 'a' is the protocol field value.  For example, a
       protocolDirID-fragment value of:
          0.0.0.1.0.0.8.0.0.0.0.1

       defines an encapsulation of ICMP (ether2.ip.icmp)"
    ADDRESS-FORMAT
       "4 octets of the IP address, in network byte order.  Each ip
       packet contains two addresses, the source address and the
       destination address."
    DECODING
       "Note: ether2.ip.ipip4.udp is a different protocolDirID than
       ether2.ip.udp, as identified in the protocolDirTable.  As such,
       two different local protocol index values will be assigned by the
       agent. E.g. (full INDEX values shown):
        ether2.ip.ipip4.udp =
            16.0.0.0.1.0.0.8.0.0.0.0.4.0.0.0.17.4.0.0.0.0
        ether2.ip.udp =
            12.0.0.0.1.0.0.8.0.0.0.0.17.3.0.0.0 "
    REFERENCE
Top   ToC   RFC2896 - Page 7
       "RFC 791 [RFC791] defines the Internet Protocol; The following
       URL defines the authoritative repository for the PROTOCOL NUMBERS
       Table:

          ftp://ftp.isi.edu/in-notes/iana/assignments/protocol-numbers"
    ::= {
       ether2     0x0800,
       llc        0x06,
       snap       0x0800,
          -- ip         4,           ** represented by the ipip4 macro
          -- ip         94,          ** represented by the ipip macro
       802-1Q     0x0800,         -- [0.0.8.0]
       802-1Q     0x02000006      -- 1Q-LLC [2.0.0.6]
    }

 -- ****************************************************************
 --
 --                        Children of IP
 --
 -- ****************************************************************

icmp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Message Control Protocol"
    REFERENCE
       "RFC 792 [RFC792] defines the Internet Control Message Protocol."
    ::= {
     ip 1,
     ipip4 1,
     ipip 1
    }

igmp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Group Management Protocol; IGMP is used by IP hosts to
       report their host group memberships to any immediately-
       neighboring multicast routers."
    REFERENCE
       "Appendix A of Host Extensions for IP Multicasting [RFC1112]
       defines the Internet Group Management Protocol."
    ::= {
     ip 2,
     ipip4 2,
     ipip 2
Top   ToC   RFC2896 - Page 8
    }

ggp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Gateway-to-Gateway Protocol; DARPA Internet Gateway
       (historical)"
    REFERENCE
       "RFC 823 [RFC823] defines the Gateway-to-Gateway Protocol."
    ::= {
     ip 3,
     ipip4 3,
     ipip 3
    }

ipip4 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES {
     hasChildren(0),
     addressRecognitionCapable(1)
    }
    DESCRIPTION
       "IP in IP Tunneling"
    CHILDREN
       "Children of 'ipip4' are selected and encoded in the same manner
       as children of IP."
    ADDRESS-FORMAT
       "The 'ipip4' address format is the same as the IP address
       format."
    DECODING
       "Note: ether2.ip.ipip4.udp is a different protocolDirID than
       ether2.ip.udp, as identified in the protocolDirTable.  As such,
       two different local protocol index values will be assigned by the
       agent. E.g. (full INDEX values shown):
        ether2.ip.ipip4.udp =
            16.0.0.0.1.0.0.8.0.0.0.0.4.0.0.0.17.4.0.0.0.0
        ether2.ip.udp =
            12.0.0.0.1.0.0.8.0.0.0.0.17.3.0.0.0 "
    REFERENCE
       "RFC 1853 [RFC1853] defines IP in IP over Protocol 4."
    ::= {
     ip 4,
     ipip4 4,
     ipip 4
    }

st PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 9
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Stream Protocol Version 2 (ST2); (historical) ST2 is an
       experimental resource reservation protocol intended to provide
       end-to-end real-time guarantees over an internet."
    REFERENCE
       "RFC 1819 [RFC1819] defines version 2 of the Internet Stream
       Protocol."
    ::= {
     ip 5,
     ipip4 5,
     ipip 5
    }

tcp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES {
      hasChildren(0)
    }
    DESCRIPTION
       "Transmission Control Protocol"
    CHILDREN
       "Children of TCP are identified by the 16 bit Source or
       Destination Port value as specified in RFC 793. They are encoded
       as [ 0.0.a.b], where 'a' is the MSB and 'b' is the LSB of the
       port value. Both bytes are encoded in network byte order.  For
       example, a protocolDirId-fragment of:
           0.0.0.1.0.0.8.0.0.0.0.6.0.0.0.23

       identifies an encapsulation of the telnet protocol
       (ether2.ip.tcp.telnet)"
    REFERENCE
       "RFC 793 [RFC793] defines the Transmission Control Protocol.

       The following URL defines the authoritative repository for
       reserved and registered TCP port values:

         ftp://ftp.isi.edu/in-notes/iana/assignments/port-numbers"
    ::=  {
     ip 6,
     ipip4 6,
     ipip 6
    }

egp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
Top   ToC   RFC2896 - Page 10
    DESCRIPTION
       "Exterior Gateway Protocol (historical)"
    REFERENCE
       "RFC 904 [RFC904] defines the Exterior Gateway Protocol."
    ::= {
     ip  8,
     ipip4  8,
     ipip  8
    }

igp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Any private interior gateway."
    REFERENCE
       "[RFC1700]"
    ::= {
     ip  9,
     ipip4  9,
     ipip  9
    }

nvp2 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "NVP-II; Network Voice Protocol"
    REFERENCE
       "RFC 741 [RFC741] defines the Network Voice Protocol"
    ::= {
     ip 11,
     ipip4 11,
     ipip 11
    }

pup PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "PUP Protocol"
    REFERENCE
       "Xerox"
    ::= {
     ip 12,
     ipip4 12,
     ipip 12
    }
Top   ToC   RFC2896 - Page 11
xnet PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Cross Net Debugger (historical)"
    REFERENCE
       "[IEN158]"
    ::= {
     ip  15,
     ipip4  15,
     ipip  15
    }

chaos PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "CHAOS Protocol; historical"
    REFERENCE
       "J. Noel Chiappa  <JNC@XX.LCS.MIT.EDU>"
    ::= {
     ip 16,
     ipip4 16,
     ipip 16
    }

udp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES {
      hasChildren(0)
    }
    DESCRIPTION
       "User Datagram Protocol"
    CHILDREN
       "Children of UDP are identified by the 16 bit Source or
       Destination Port value as specified in RFC 768. They are encoded
       as [ 0.0.a.b ], where 'a' is the MSB and 'b' is the LSB of the
       port value. Both bytes are encoded in network byte order.  For
       example, a protocolDirId-fragment of:
           0.0.0.1.0.0.8.0.0.0.0.17.0.0.0.161

       identifies an encapsulation of SNMP (ether2.ip.udp.snmp)"
    REFERENCE
       "RFC 768 [RFC768] defines the User Datagram Protocol.

       The following URL defines the authoritative repository for
       reserved and registered UDP port values:
Top   ToC   RFC2896 - Page 12
         ftp://ftp.isi.edu/in-notes/iana/assignments/port-numbers"
   ::= {
     ip 17,
     ipip4 17,
     ipip 17
    }

mux PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Multiplexing Protocol (historical)"
    REFERENCE
       "IEN-90 [IEN-90] defines the Multiplexing Protocol"
    ::= {
     ip 18,
     ipip4 18,
     ipip 18
    }

hmp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Host Monitoring Protocol; historical"
    REFERENCE
       "RFC 869 [RFC869] defines the Host Monitoring Protocol"
    ::= {
     ip  20,
     ipip4  20,
     ipip  20
    }

xns-idp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "XEROX NS IDP"
    REFERENCE
       "Xerox Corporation"
    ::= {
     ip  22,
     ipip4  22,
     ipip  22
    }

rdp PROTOCOL-IDENTIFIER
    PARAMETERS { }
Top   ToC   RFC2896 - Page 13
    ATTRIBUTES { }
    DESCRIPTION
       "Reliable Data Protocol"
    REFERENCE
       "RFC 908 [RFC908] defines the original protocol; RFC 1151
       [RFC1151] defines version 2 of the Reliable Data Protocol."
    ::= {
     ip 27,
     ipip4 27,
     ipip 27
    }

irtp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Reliable Transaction Protocol"
    REFERENCE
       "RFC 938 [RFC938] defines the Internet Reliable Transaction
       Protocol functional and  interface specification."
    ::= {
     ip 28,
     ipip4 28,
     ipip 28
    }

iso-tp4  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "ISO Transport Protocol Specification"
    REFERENCE
       "RFC 905 [RFC905] defines the ISO Transport Protocol
       Specification; ISO DP 8073"
    ::= {
     ip  29,
     ipip4  29,
     ipip  29
    }

netblt PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Bulk Data Transfer Protocol; historical"
    REFERENCE
       "RFC 998 [RFC998] defines NETBLT: A Bulk Data Transfer Protocol."
    ::= {
Top   ToC   RFC2896 - Page 14
     ip 30,
     ipip4 30,
     ipip 30
    }

mfe-nsp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "MFE Network Services Protocol; historical"
    REFERENCE
       "Shuttleworth, B., 'A Documentary of MFENet, a National Computer
       Network', UCRL-52317, Lawrence Livermore Labs, Livermore,
       California, June 1977."
    ::= {
     ip 31,
     ipip4 31,
     ipip 31
    }

idpr PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Inter-Domain Policy Routing Protocol"
    REFERENCE
       "RFC 1479 [RFC1479] defines Version 1 of the Inter-Domain Policy
       Routing Protocol."
    ::= {
     ip 35,
     ipip4 35,
     ipip 35
    }

idpr-cmtp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "IDPR Control Message Transport Protocol"
    REFERENCE
       "RFC 1479 [RFC1479] defines Version 1 of the Inter-Domain Policy
       Routing Protocol."
    ::= {
     ip 38,
     ipip4 38,
     ipip 38
    }
Top   ToC   RFC2896 - Page 15
sdrp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Source Demand Routing Protocol"
    REFERENCE
       "RFC 1940 [RFC1940] defines version 1 of the Source Demand
       Routing: Packet Format and Forwarding Specification"
    ::= {
     ip 42,
     ipip4 42,
     ipip 42
    }

idrp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Inter-Domain Routing Protocol"
    REFERENCE
       "RFC 1745 [RFC1745] defines BGP4/IDRP for IP."
    ::= {
     ip 45,
     ipip4 45,
     ipip 45
    }

rsvp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Resource Reservation Setup Protocol"
    REFERENCE
       "Resource ReSerVation Protocol (RSVP); Version 1 Functional
        Specification [RFC2205]."
    ::= {
     ip 46,
     ipip4 46,
     ipip 46
    }

gre PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "General Routing Encapsulation"
    REFERENCE
        "RFC 1701 [RFC1701] defines Generic Routing Encapsulation (GRE);
Top   ToC   RFC2896 - Page 16
       RFC 1702 [RFC1702] defines Generic Routing Encapsulation over
       IPv4 networks"
    ::= {
     ip 47,
     ipip4 47,
     ipip 47
    }

nhrp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "NBMA Next Hop Resolution Protocol (NHRP)"
    REFERENCE
       "RFC 2332 [RFC2332] defines the Next Hop Resolution Protocol."
    ::= {
     ip 54,
     ipip4 54,
     ipip 54
    }

priv-host PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any internal host protocol."
    REFERENCE
       "[RFC1700]"
    ::= {
     ip 61,
     ipip4 61,
     ipip 61
    }

priv-net PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any local network protocol."
    REFERENCE
       "[RFC1700]"
    ::= {
     ip 63,
     ipip4 63,
     ipip 63
    }

priv-distfile PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 17
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any distributed file system."
    REFERENCE
       "[RFC1700]"
    ::= {
     ip 68,
     ipip4 68,
     ipip 68
    }

dgp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Dissimilar Gateway Protocol"
    REFERENCE
       "M/A-COM Government Systems, 'Dissimilar Gateway Protocol
       Specification, Draft Version', Contract no. CS901145, November
       16, 1987."
    ::= {
     ip 86,
     ipip4 86,
     ipip 86
    }

igrp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "IGRP; Cisco routing protocol"
    REFERENCE
       "Cisco Systems, Inc."
    ::= {
     ip 88,
     ipip4 88,
     ipip 88
    }

ospf PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Open Shortest Path First Interior GW Protocol (OSPFIGP)."
    REFERENCE
       "RFC 1583 [RFC1583] defines version 2 of the OSPF protocol."
    ::= {
Top   ToC   RFC2896 - Page 18
     ip 89,
     ipip4 89,
     ipip 89
    }

mtp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Multicast Transport Protocol"
    REFERENCE
       "RFC 1301 [RFC1301] defines the Multicast Transport Protocol."
    ::= {
     ip 92,
     ipip4 92,
     ipip 92
    }

ax-25 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "AX.25 Frame Encapsulation"
    REFERENCE
       "RFC 1226 [RFC1226] defines Internet Protocol Encapsulation of
       AX.25 Frames."
    ::= {
     ip 93,
     ipip4 93,
     ipip 93
    }

ipip PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES {
     hasChildren(0),
     addressRecognitionCapable(1)
    }
    DESCRIPTION
       "IP-within-IP Encapsulation Protocol"
    CHILDREN
       "Children of 'ipip' are selected and encoded in the same manner
       as children of IP."
    ADDRESS-FORMAT
       "The 'ipip' address format is the same as the IP address format."
    DECODING
       "Note: ether2.ip.ipip.udp is a different protocolDirID than
       ether2.ip.udp, as identified in the protocolDirTable.  As such,
Top   ToC   RFC2896 - Page 19
       two different local protocol index values will be assigned by the
       agent. E.g. (full INDEX values shown):
        ether2.ip.ipip.udp =
            16.0.0.0.1.0.0.8.0.0.0.0.94.0.0.0.17.4.0.0.0.0
        ether2.ip.udp =
            12.0.0.0.1.0.0.8.0.0.0.0.17.3.0.0.0 "
    REFERENCE
       "RFC 2003 [RFC2003] defines IP Encapsulation within IP."
    ::= {
     ip 94,
     ipip4 94,
     ipip 94
    }

encap PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Encapsulation Header; A Scheme for an Internet Encapsulation
       Protocol: Version 1"
    REFERENCE
       "RFC 1241 [RFC1241] defines version 1 of the ENCAP Protocol."
    ::= {
     ip 98,
     ipip4 98,
     ipip 98
    }

priv-encript PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private encryption scheme."
    REFERENCE
       "[RFC1700]"
    ::= {
     ip 99,
     ipip4 99,
     ipip 99
    }

 -- ****************************************************************
 --
 --                    Children of UDP and TCP
 --
 -- ****************************************************************

tcpmux  PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 20
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "TCP Port Service Multiplexer Port."
    REFERENCE
       "RFC 1078 [RFC1078] defines the TCP Port Service Multiplexer
       Protocol."
    ::= { tcp 1 }

rje  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Job Entry Protocol; RJE Logger Port; (historical)."
    REFERENCE
       "RFC 407 [RFC407] defines the Remote Job Entry Protocol."
    ::= { tcp 5 }

echo  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Echo Protocol for debugging  TCP and UDP transports."
    REFERENCE
       "RFC 862 [RFC862] defines the Echo Protocol."
    ::= {
       tcp 7,
       udp 7  }

discard  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Discard Protocol for debugging TCP and UDP transports."
    REFERENCE
       "RFC 863 [RFC863] defines the Discard Protocol."
    ::= {
       tcp 9,
       udp 9  }

systat  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Retrieve the Active Users list; a debugging tool for TCP and UDP
       transports."
    REFERENCE
       "RFC 866 [RFC866] defines the Active Users Protocol."
Top   ToC   RFC2896 - Page 21
    ::= {
       tcp 11,
       udp 11  }

daytime  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Retrieve the current time of day; a debugging tool for TCP and
       UDP transports."
    REFERENCE
       "RFC 867 [RFC867] defines the Daytime Protocol."
    ::= {
       tcp 13,
       udp 13  }

qotd  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Quote of the Day Protocol; retrieve a short message (up to 512
       bytes); a debugging tool for TCP and UDP transports."
    REFERENCE
       "RFC 865 [RFC865] defines the Quote of the Day Protocol."
    ::= {
       tcp 17,
       udp 17  }

msp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Message Send Protocol"
    REFERENCE
       "RFC 1312 [RFC1312] defines the Message Send Protocol."

    ::= {
       tcp 18,
       udp 18  }

chargen  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Character Generator Protocol; a debugging tool for TCP and UDP
       transports."
    REFERENCE
       "RFC 864 [RFC864] defines the Character Generator Protocol."
Top   ToC   RFC2896 - Page 22
    ::= {
       tcp 19,
       udp 19  }

ftp-data PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "The File Transfer Protocol Data Port; the FTP Server process
       default data-connection port. "
    REFERENCE
       "RFC 959 [RFC959] defines the File Transfer Protocol.  Refer to
       section 3.2 of [RFC959] for details on FTP data connections."
    ::= { tcp 20 }

ftp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "The File Transfer Protocol Control Port; An FTP client initiates
       an FTP control connection by sending FTP commands from user port
       (U) to this port."
    REFERENCE
       "RFC 959 [RFC959] defines the File Transfer Protocol."
    ::= { tcp 21 }

telnet PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "The Telnet Protocol; The purpose of the TELNET Protocol is to
       provide a fairly general, bi-directional, eight-bit byte oriented
       communications facility.  Its primary goal is to allow a standard
       method of interfacing terminal devices and terminal-oriented
       processes to each other. "
    REFERENCE
       "RFC 854 [RFC854] defines the basic Telnet Protocol."
    ::= { tcp 23 }

priv-mail PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private mail system."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 24,
       udp 24 }
Top   ToC   RFC2896 - Page 23
smtp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "The Simple Mail Transfer Protocol; SMTP control and data
       messages are sent on this port."
    REFERENCE
       "RFC 821 [RFC821] defines the basic Simple Mail Transfer
       Protocol."
    ::= { tcp 25 }

priv-print PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private printer server."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 35,
       udp 35  }

time PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Time Protocol"
    REFERENCE
       "RFC 868 [RFC868] defines the Time Protocol."
    ::= { tcp 37,
       udp 37 }

rap PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Route Access Protocol"
    REFERENCE
       "RFC 1476 [RFC1476] defines the Internet Route Access Protocol."
    ::= { tcp 38 }

rlp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Resource Location Protocol"
    REFERENCE
       "RFC 887 [RFC887] defines the Resource Location Protocol."
    ::= { udp 39 }
Top   ToC   RFC2896 - Page 24
graphics PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Graphics Protocol"
    REFERENCE
       "RFC 493 [RFC493] defines the Graphics Protocol."
    ::= { tcp 41,
       udp 41  }

nameserver  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Host Name Server Protocol"
    REFERENCE
       "IEN 116 [IEN116] defines the Internet Name Server."
    ::= { udp 42 }

nicname  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "NICNAME/WHOIS Protocol"
    REFERENCE
       "RFC 954 [RFC954] defines the NICNAME/Who Is Protocol."
    ::= { tcp 43 }

mpm-flags  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "MPM FLAGS Protocol; (historical)."
    REFERENCE
       "RFC 759 [RFC759] defines the Message Processing Module."
    ::= { tcp 44 }

mpm  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Message Processing Module -- Receiver; (historical)."
    REFERENCE
       "RFC 759 [RFC759] defines the Message Processing Module."
    ::= { tcp 45 }

mpm-snd  PROTOCOL-IDENTIFIER
    PARAMETERS { }
Top   ToC   RFC2896 - Page 25
    ATTRIBUTES { }
    DESCRIPTION
       "Message Processing Module -- Default Send; (historical)."
    REFERENCE
       "RFC 759 [RFC759] defines the Message Processing Module."
    ::= { tcp 46 }

tacacs  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Login Host Protocol (TACACS)"
    REFERENCE
       "An Access Control Protocol, Sometimes Called TACACS [RFC1492]."
    ::= { tcp 49 }

re-mail-ck  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Mail Checking Protocol"
    REFERENCE
       "RFC 1339 [RFC1339] defines the Remote Mail Checking Protocol."
    ::= { udp 50 }

xns-time  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "XNS Time Protocol"
    REFERENCE
       "Xerox Corporation"
    ::= { tcp 52,
       udp 52 }

domain PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Domain Name Service Protocol; DNS may be transported by either
       UDP [RFC768] or TCP [RFC793].  If the transport is UDP, DNS
       requests restricted to 512 bytes in length may be sent to this
       port."
    REFERENCE
       "RFC 1035 [RFC1035] defines the Bootstrap Protocol."
    ::= { udp 53,
       tcp 53  }
Top   ToC   RFC2896 - Page 26
xns-ch PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "XNS Clearinghouse"
    REFERENCE
       "Xerox Corporation"
    ::= { tcp 54,
       udp 54 }

xns-auth PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "XNS Authentication Protocol"
    REFERENCE
       "Xerox Corporation"
    ::= { tcp 56,
       udp 56 }

priv-term PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private terminal access
       protocol."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 57,
       udp 57 }

xns-mail PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "XNS Mil Protocol"
    REFERENCE
       "Xerox Corporation"
    ::= { tcp 58,
       udp 58 }

priv-file PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private file service."
    REFERENCE
       "[RFC1700]"
Top   ToC   RFC2896 - Page 27
    ::= { tcp 59,
       udp 59 }

tacacs-ds PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Default Server Port; TACACS Access Control Protocol Database
       Service."
    REFERENCE
       "RFC 1492 [RFC1492] defines the TACACS Protocol."
    ::= { tcp 65 }

sqlnet PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Oracle SQL*NET"
    REFERENCE
       "Oracle Corporation"
    ::= { tcp 66 }

bootps PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Bootstrap Protocol Server Protocol; BOOTP Clients send requests
       (usually broadcast) to the bootps port."
    REFERENCE
       "RFC 951 [RFC951] defines the Bootstrap Protocol."
    ::= { udp 67 }

bootpc PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Bootstrap Protocol Client Protocol; BOOTP Server replies are
       sent to the BOOTP Client using this destination port."
    REFERENCE
       "RFC 951 [RFC951] defines the Bootstrap Protocol."
    ::= { udp 68 }

tftp PROTOCOL-IDENTIFIER
    PARAMETERS {
     tracksSessions(1)
    }
    ATTRIBUTES { }
    DESCRIPTION
Top   ToC   RFC2896 - Page 28
       "Trivial File Transfer Protocol; Only the first packet of each
       TFTP transaction will be sent to port 69. If the tracksSessions
       attribute is set, then packets for each TFTP transaction will be
       attributed to tftp, instead of the unregistered port numbers that
       will be encoded in subsequent packets."
    REFERENCE
       "RFC 1350 [RFC1350] defines the TFTP Protocol (revision 2);
        RFC 1782 [RFC1782] defines TFTP Option Extensions;
        RFC 1783 [RFC1783] defines the TFTP Blocksize Option;
        RFC 1784 [RFC1784] defines TFTP Timeout Interval and Transfer
        Size  Options."
    ::= { udp 69 }

gopher PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Gopher Protocol"
    REFERENCE
       "RFC 1436 [RFC1436] defines the Gopher Protocol."
    ::= { tcp 70 }

netrjs-1 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Job Service Protocol; (historical)."
    REFERENCE
       "RFC 740 [RFC740] defines the NETRJS Protocol."
    ::= { tcp 71 }

netrjs-2 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Job Service Protocol; (historical)."
    REFERENCE
       "RFC 740 [RFC740] defines the NETRJS Protocol."
    ::= { tcp 72 }

netrjs-3 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Job Service Protocol; (historical)."
    REFERENCE
       "RFC 740 [RFC740] defines the NETRJS Protocol."
    ::= { tcp 73 }
Top   ToC   RFC2896 - Page 29
netrjs-4 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Job Service Protocol; (historical)."
    REFERENCE
       "RFC 740 [RFC740] defines the NETRJS Protocol."
    ::= { tcp 74 }

priv-dialout PROTOCOL-IDENTIFIER

    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private dial out service."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 75,
       udp 75 }

priv-rje PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private remote job entry
       service."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 77,
       udp 77 }

finger PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Finger User Information Protocol"
    REFERENCE
       "RFC 1288 [RFC1288] defines the finger protocol."
    ::= { tcp 79 }

www-http PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Hypertext Transfer Protocol"
    REFERENCE
       "RFC 1945 [RFC1945] defines the Hypertext Transfer Protocol
(HTTP/1.0).
Top   ToC   RFC2896 - Page 30
        RFC 2068 [RFC2068] defines the Hypertext Transfer Protocol
(HTTP/1.1).
        RFC 2069 [RFC2069] defines an Extension to HTTP: Digest Access
           Authentication.
        RFC 2109 [RFC2109] defines the HTTP State Management Mechanism.
        RFC 2145 [RFC2145] defines the use and interpretation of HTTP
           version numbers."
    ::= { tcp 80 }

priv-termlink PROTOCOL-IDENTIFIER

    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Pseudo-protocol reserved for any private terminal link
       protocol."
    REFERENCE
       "[RFC1700]"
    ::= { tcp 87,
       udp 87 }

kerberos PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "The Kerberos Network Authentication Service (V5)"
    REFERENCE
       "RFC 1510 [RFC1510] defines the Kerberos protocol."
    ::= { udp 88 }

supdup PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "SUPDUP Display; (historical)"
    REFERENCE
       "RFC 734 [RFC734] defines the SUPDUP Protocol."
    ::= { tcp 95 }

dixie PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "DIXIE Directory Service"
    REFERENCE
       "RFC 1249 [RFC1249] defines the DIXIE Protocol."
    ::= { tcp 96,
       udp 96 }
Top   ToC   RFC2896 - Page 31
hostname  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "NIC Internet Hostname Server Protocol; (historical)"
    REFERENCE
       "RFC 953 [RFC953] defines the Hostname Server Protocol."
    ::= { tcp 101 }

3com-tsmux PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "3COM-TSMUX"
    REFERENCE
       "3Com, Inc."
    ::= { tcp 106,
       udp 106 }

rtelnet  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote User Telnet Protocol; (historical)."
    REFERENCE
       "RFC 818 [RFC818] defines the Remote User Telnet Service."
    ::= { tcp 107 }

pop2 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Post Office Protocol -- Version 2. Clients establish connections
       with POP2 servers by using this destination port number.
       Historical."
    REFERENCE
       "RFC 937 [RFC937] defines Version 2 of the Post Office Protocol."
    ::= { tcp 109 }

pop3 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Post Office Protocol -- Version 3. Clients establish connections
       with POP3 servers by using this destination port number."
    REFERENCE
       "RFC 1725 [RFC1725] defines Version 3 of the Post Office
       Protocol."
Top   ToC   RFC2896 - Page 32
    ::= { tcp 110,
       udp 110 }     -- RFC defines tcp use

sunrpc PROTOCOL-IDENTIFIER

    PARAMETERS {
        tracksSessions(1) -- learn port mapping of programs
    }
    ATTRIBUTES {
        hasChildren(0)   -- port mapper function numbers
    }
    DESCRIPTION
       "SUN Remote Procedure Call Protocol. Port mapper function
       requests are sent to this destination port."
    CHILDREN
       "Specific RPC functions are represented as children of the sunrpc
       protocol.  Each 'RPC function protocol' is identified by its
       function number assignment. RPC function number assignments are
       defined by different naming authorities, depending on the
       function identifier value.
       From [RFC1831]:

       Program numbers are given out in groups of hexadecimal 20000000
       (decimal 536870912) according to the following chart:

                     0 - 1fffffff   defined by rpc@sun.com
              20000000 - 3fffffff   defined by user
              40000000 - 5fffffff   transient
              60000000 - 7fffffff   reserved
              80000000 - 9fffffff   reserved
              a0000000 - bfffffff   reserved
              c0000000 - dfffffff   reserved
              e0000000 - ffffffff   reserved

       Children of 'sunrpc' are encoded as [ 0.0.0.111], the protocol
       identifier component for 'sunrpc', followed by [ a.b.c.d ], where
       a.b.c.d is the 32 bit binary RPC program number encoded in
       network byte order.  For example, a protocolDirID-fragment value
       of:
           0.0.0.111.0.1.134.163

       defines the NFS function (and protocol).

       Children are named as 'sunrpc' followed by the RPC function
       number in base 10 format. For example, NFS would be named:
           'sunrpc 100003'."
    DECODING
       "The first packet of many SUNRPC transactions is sent to the
Top   ToC   RFC2896 - Page 33
       port- mapper program, and therefore decoded statically by
       monitoring RFC portmap requests [RFC1831]. Any subsequent packets
       must be decoded and correctly identified by 'remembering' the
       port assignments used in each RPC function call (as identified
       according to the procedures in the RPC Specification Version 2
       [RFC1831]).

       In some cases the port mapping for a particular protocol is well
       known and hard coded into the requesting client.  In these cases
       the client will not send portmap requests; instead it will send
       the SUNRPC request directly to the well known port.  These cases
       are rare and are being eliminated over time.  NFS is the most
       significant SUNRPC program of this class.  Such programs should
       still be declared as children of SUNRPC as described under
       CHILDREN above.  How an implementation detects this behaviour and
       handles it is beyond the scope of this document.

       The 'tracksSessions(1)' PARAMETER bit is used to indicate whether
       the probe can (and should) monitor portmapper activity to
       correctly track SUNRPC connections."
    REFERENCE
       "RFC 1831 [RFC1831] defines the Remote Procedure Call Protocol
       Version 2.  The authoritative list of RPC Functions is identified
       by the URL:
           ftp://ftp.isi.edu/in-notes/iana/assignments/sun-rpc-numbers"
    ::= { tcp 111,
       udp 111 }

auth PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Authentication Service; Identification Protocol."
    REFERENCE
       "RFC 1413 [RFC1413] defines the Identification Protocol."
    ::= { tcp 113 }

sftp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Simple File Transfer Protocol; (historical)."
    REFERENCE
       "RFC 913 [RFC913] defines the Simple File Transfer Protocol."
    ::= { tcp 115 }

uucp-path  PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 34
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "UUCP Path Service"
    REFERENCE
       "RFC 915 [RFC915] defines the Network Mail Path Service."
    ::= { tcp 117 }

nntp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Network News Transfer Protocol"
    REFERENCE
       "RFC 977 [RFC977] defines the Network News Transfer Protocol."
    ::= { tcp 119 }

cfdptkt PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "CFDPTKT; Coherent File Distribution Protocol"
    REFERENCE
       "RFC 1235 [RFC1235] defines the Coherent File Distribution
       Protocol."
    ::= { udp 120 }

ntp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Network Time Protocol"
    REFERENCE
       "RFC 1305 [RFC1305] defines version 3 of the Network Time
       Protocol."
    ::= { udp 123 }

pwdgen  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Password Generator Protocol"
    REFERENCE
       "RFC 972 [RFC972] defines the Password Generator Protocol."
    ::= { tcp 129,
       udp 129  }

cisco-fna  PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 35
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "cisco FNATIVE"
    REFERENCE
       "Cisco Systems, Inc."
    ::= { tcp 130,
       udp 130 }

cisco-tna  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "cisco TNATIVE"
    REFERENCE
       "Cisco Systems, Inc."
    ::= { tcp 131,
       udp 131 }

cisco-sys  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "cisco SYSMAINT"
    REFERENCE
       "Cisco Systems, Inc."
    ::= { tcp 132,
       udp 132 }

statsrv  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Statistics Server; (historical)."
    REFERENCE
       "RFC 996 [RFC996] defines the Statistics Server Protocol."
    ::= { tcp 133,
       udp 133 }

 -- defined as nbt-name in IPX section
 -- netbios-ns      137/tcp    NETBIOS Name Service
 -- netbios-ns      137/udp    NETBIOS Name Service
 -- defined as nbt-data in IPX section
 -- netbios-dgm     138/tcp    NETBIOS Datagram Service
 -- netbios-dgm     138/udp    NETBIOS Datagram Service

 -- defined as nbt-session in IPX section
 -- netbios-ssn     139/tcp    NETBIOS Session Service
Top   ToC   RFC2896 - Page 36
 -- netbios-ssn     139/udp    NETBIOS Session Service

imap2  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Interactive Mail Access Protocol v2;
        Internet Message Access Protocol v4 (IMAP4) also uses this
       server port."
    REFERENCE
       "RFC 1064 [RFC1064] defines Version 2 of the Interactive Mail
       Access
        Protocol.
        RFC 1730 [RFC1730] defines Version 4 of the Internet Message
       Access
        Protocol."
    ::= { tcp 143 }

iso-tp0  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "ISO-IP0; ISO-TP0 bridge between TCP and X.25"
    REFERENCE
       "RFC 1086 [RFC1086] defines the ISO-TP0 protocol."
    ::= { tcp 146,
       udp 146 }

iso-ip  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "ISO-IP; Use of the Internet as a Subnetwork for Experimentation
       with the OSI Network Layer"
    REFERENCE
       "RFC 1070 [RFC1070] defines the ISO-IP Protocol."
    ::= { tcp 147,
       udp 147 }

hems  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "HEMS; High Level Entity Management System; (historical)."
    REFERENCE
       "RFC 1021 [RFC1021] defines HEMS."
    ::= { tcp 151 }
Top   ToC   RFC2896 - Page 37
bftp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Background File Transfer Program"
    REFERENCE
       "RFC 1068 [RFC1068] defines the Background File Transfer
       Program."
    ::= { tcp 152 }

sgmp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Simple Gateway Monitoring Protocol; (historical)."
    REFERENCE
       "RFC 1028 [RFC1028] defines the Simple Gateway Monitoring
       Protocol."
    ::= { udp 153 }

pcmail-srv  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "PCMail Server; Distributed Mail System Protocol (DMSP)"
    REFERENCE
       "RFC 1056 [RFC1056] defines the PCMAIL Protocol."
    ::= { tcp 158 }

sgmp-traps  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Simple Gateway Monitoring Protocol Traps; (historical)."
    REFERENCE
       "RFC 1028 [RFC1028] defines the Simple Gateway Monitoring

       Protocol."
    ::= { udp 160 }

 -- snmp and snmptrap found in the Protocol-Independent section
 -- snmp            161/udp    SNMP
 -- snmptrap        162/udp    SNMPTRAP

cmip-man  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
Top   ToC   RFC2896 - Page 38
       "CMIP/TCP (CMOT) Manager; (historical)."
    REFERENCE
       "RFC 1095 [RFC1095] defines the Common Management Information
       Services and Protocol over TCP/IP."
    ::= { tcp 163,
       udp 163 }

cmip-agent  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "CMIP/TCP (CMOT) Agent; (historical)."
    REFERENCE
       "RFC 1095 [RFC1095] defines the Common Management Information
       Services and Protocol over TCP/IP."
    ::= { tcp 164,
       udp 164 }

xdmcp PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "X Display Manager Control Protocol"
    REFERENCE
       "X11 Consortium"
    ::= { udp 177 }

bgp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Border Gateway Protocol"
    REFERENCE
       "RFC 1267 [RFC1267] defines version 3 of the Border Gateway

       Protocol."
    ::= { tcp 179 }

remote-kis  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote-Knowbot Information Service (KIS)"
    REFERENCE
       "RFC 1739 [RFC1739] describes the KNOWBOT Protocol."
    ::= { tcp 185,
       udp 185 }
Top   ToC   RFC2896 - Page 39
kis  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Knowbot Information Service (KIS)"
    REFERENCE
       "RFC 1739 [RFC1739] describes the KNOWBOT Protocol."
    ::= { tcp 186,
       udp 186 }

irc  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Relay Chat Protocol"
    REFERENCE
       "RFC 1459 [RFC1459] defines the Internet Relay Chat Protocol."
    ::= { tcp 194,
       udp 194 }

smux PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "SMUX; SNMP MUX Protocol and MIB; (historical)."
    REFERENCE
       "RFC 1227 [RFC1227] defines the SMUX Protocol."
    ::= { tcp 199 }

 --
 -- AppleTalk applications are defined in the AppleTalk Stack section
 --
 -- at-rtmp         201/tcp    AppleTalk Routing Maintenance
 -- at-rtmp         201/udp    AppleTalk Routing Maintenance
 -- at-nbp          202/tcp    AppleTalk Name Binding
 -- at-nbp          202/udp    AppleTalk Name Binding
 -- at-3            203/tcp    AppleTalk Unused
 -- at-3            203/udp    AppleTalk Unused
 -- at-echo         204/tcp    AppleTalk Echo
 -- at-echo         204/udp    AppleTalk Echo
 -- at-5            205/tcp    AppleTalk Unused
 -- at-5            205/udp    AppleTalk Unused
 -- at-zis          206/tcp    AppleTalk Zone Information
 -- at-zis          206/udp    AppleTalk Zone Information
 -- at-7            207/tcp    AppleTalk Unused
 -- at-7            207/udp    AppleTalk Unused
 -- at-8            208/tcp    AppleTalk Unused
 -- at-8            208/udp    AppleTalk Unused
Top   ToC   RFC2896 - Page 40
z39-50 PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "ANSI Z39.50"
    REFERENCE
       "RFC 1729 [RFC1729] describes the Z39.50 Protocol."
    ::= { tcp 210 }

ipx-tunnel  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Tunneling IPX Traffic through IP Networks"
    REFERENCE
       "RFC 1234 [RFC1234] defines the IPX Tunnel Protocol."
    ::= { udp 213 }

mpp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Netix Message Posting Protocol"
    REFERENCE
       "RFC 1204 [RFC1204] defines the Message Posting Protocol."
    ::= { tcp 218 }

imap3  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Interactive Mail Access Protocol v3; (historical)."
    REFERENCE
       "RFC 1203 [RFC1203] defines version 3 of the Interactive Mail
       Access Protocol."
    ::= { tcp 220 }

ldap  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Lightweight Directory Access Protocol"
    REFERENCE
       "RFC 1777 [RFC1777] defines Lightweight Directory Access
       Protocol; RFC 1798 [RFC1798] defines Connection-less Lightweight
       X.500 Directory Access Protocol"
    ::= { tcp 389,       -- RFC 1777
       udp 389  }        -- RFC 1798
Top   ToC   RFC2896 - Page 41
mobileip-agent  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "IP Mobility Support"
    REFERENCE
       "RFC 2002 [RFC2002] defines the IP Mobility Support protocol."
    ::= { udp 434 }

https  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Secure HTTP; HTTP over TLS/SSL"
    REFERENCE
       "Netscape; http://home.netscape.com/eng/ssl3/"
    ::= { tcp 443 }

smtps  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "SMTP protocol over TLS/SSL"
    REFERENCE
       "Netscape; http://home.netscape.com/eng/ssl3/"
    ::= { tcp 465 }

isakmp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Internet Security Association and Key Management Protocol
       (ISAKMP)"
    REFERENCE
       "RFC 2408 [RFC2408]"
    ::= { udp 500 }

login  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "BSD Rlogin; remote login a la telnet"
    REFERENCE
       "RFC 1282 [RFC1282] defines the BSD Rlogin Protocol."
    ::= { tcp 513 }

syslog  PROTOCOL-IDENTIFIER
    PARAMETERS { }
Top   ToC   RFC2896 - Page 42
    ATTRIBUTES { }
    DESCRIPTION
       "syslog"
    REFERENCE
       "[RFC1700]"
    ::= { udp 514 }

uucp  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Unix-to-Unix copy protocol"
    REFERENCE
       "[RFC1700]"
    ::= { tcp 540 }

doom  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "DOOM Game;"
    REFERENCE
       " Id Software"
    ::= { tcp 666 }

radius  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Remote Authentication Dial In User Service (RADIUS)"
    REFERENCE
       "RFC 2138 [RFC2138] defines the Radius protocol."
    ::= { udp 1812 }

radiusacct  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "RADIUS Accounting Protocol"
    REFERENCE
       "RFC 2139 [RFC2139] defines the Radius Accounting protocol."
    ::= { udp 1813 }

 --
 -- Portmapper Functions; Children of sunrpc
 --

portmapper PROTOCOL-IDENTIFIER
Top   ToC   RFC2896 - Page 43
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "SUNRPC PORTMAPPER program.  This is the SUNRPC program which is
       used to locate the UDP/TCP ports on which other SUNRPC programs
       can be found."
    REFERENCE
       "Appendix A of RFC 1057 [RFC1057] describes the portmapper
       operation."
    ::= { sunrpc 100000 }

nfs  PROTOCOL-IDENTIFIER
    PARAMETERS { }
    ATTRIBUTES { }
    DESCRIPTION
       "Sun Network File System (NFS);"
    DECODING
       "NFS is a SUNRPC program which may or may not use the port mapper
       SUNRPC program to connect clients and servers.  In many cases the
       NFS server program runs over UDP/TCP port 2049, but an
       implementation is encouraged to perform further analysis before
       assuming that a packet to/from this port is a SUNRPC/NFS packet.
       Likewise an implementation is encouraged to track port mapper
       activity to spot cases where it is used to locate the SUNRPC/NFS
       program as this is more robust."
    REFERENCE
       "The NFS Version 3 Protocol Specification is defined in RFC 1813
       [RFC1813]."
    ::= {
     sunrpc 100003       --  [0.1.134.163]
    }

xwin PROTOCOL-IDENTIFIER
    PARAMETERS {
        tracksSessions(1)
    }
    ATTRIBUTES { }
    DESCRIPTION
       "X Windows Protocol"
    DECODING
       "The X Windows Protocol when run over UDP/TCP normally runs over
       the well known port 6000.  It can run over any port in the range
       6000 to 6063, however.  If the tracksSessions(1) parameter bit is
       set the agent can and should detect such X Window sessions and
       report them as the X protocol."
    REFERENCE
         "The X Windows Protocol is defined by TBD"
    ::= {
Top   ToC   RFC2896 - Page 44
      tcp 6000,
      udp 6000
      -- lat ?
    }



(page 44 continued on part 3)

Next Section