RFC 2515
Definitions of Managed Objects for ATM Management
9. Definitions
ATM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, IpAddress, mib-2 FROM SNMPv2-SMI DisplayString, RowStatus, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF InterfaceIndex, ifIndex FROM IF-MIB AtmAddr, AtmConnKind, AtmConnCastType, AtmServiceCategory, AtmTrafficDescrParamIndex, AtmVpIdentifier, AtmVcIdentifier, AtmVorXAdminStatus, AtmVorXLastChange, AtmVorXOperStatus, atmNoClpNoScr FROM ATM-TC-MIB; atmMIB MODULE-IDENTITY LAST-UPDATED "9810191200Z" ORGANIZATION "IETF AToM MIB Working Group" CONTACT-INFO " Kaj Tesink Postal: Bellcore 331 Newman Springs Road Red Bank, NJ 07701 Tel: 732-758-5254 Fax: 732-758-2269 E-mail: kaj@bellcore.com" DESCRIPTION "This is the MIB Module for ATM and AAL5-related objects for managing ATM interfaces, ATM virtual
links, ATM cross-connects, AAL5 entities, and
and AAL5 connections."
REVISION "9810191200Z"
DESCRIPTION
"The initial revision of this module was published
as RFC 1695. Key revisions include:
o Textual Conventions and OBJECT IDENTITIES have
been moved to a separate MIB module.
o Applicability of objects to PVCs, SVCs and Soft
PVCs has been clarified.
o DEFVAL clauses have been added.
o The relationship of ifIndex values with different
layers and sublayers related to ATM has been
clarified.
o atmTrafficQosClass has been deprecated
and replaced with atmServiceCategory.
o atmInterfaceCurrentMaxVpiBits and
atmInterfaceCurrentMaxVciBits have been added with
a description on their relationship with other
objects.
o atmInterfaceAddressType and atmInterfaceAdminAddress
have been deprecated and replaced by
atmInterfaceSubscrAddress.
o atmInterfaceTCAlarmState has been clarified.
o atmTrafficDescrParamIndexNext has been introduced
in order to provide a manager a free
atmTrafficDescrParamIndex value.
o The atmTrafficFrameDiscard capability has been added.
o A connection topology type (atmVpl/VclCastType) and
a call control type (atmVpl/VclConnKind) have been
added.
o aal2 has been added to atmVccAalType."
REVISION "9406072245Z"
DESCRIPTION
"The RFC1695 version of this MIB module."
::= { mib-2 37 }
atmMIBObjects OBJECT IDENTIFIER ::= {atmMIB 1}
-- {atmMIBObjects 1} has been moved to a separate
-- specification [19].
-- This ATM MIB Module consists of the following tables:
-- (1) ATM Interface configuration table
-- (2) ATM Interface DS3 PLCP table
-- (3) ATM Interface TC Sublayer table
-- (4) Atm Traffic Descriptor table
-- (5) ATM Interface VPL configuration table
-- (6) ATM Interface VCL configuration table
-- (7) ATM VP Cross Connect table (for PVCs)
-- (8) ATM VC Cross Connect table (for PVCs)
-- (9) ATM Interface AAL5 VCC performance statistics
-- table
-- ATM Interface Configuration Parameters Table
-- This table contains ATM specific
-- configuration information associated with
-- an ATM interface beyond those
-- supported using the ifTable.
atmInterfaceConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM local interface
configuration parameters, one entry per ATM
interface port."
::= { atmMIBObjects 2 }
atmInterfaceConfEntry OBJECT-TYPE
SYNTAX AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains ATM interface configuration
parameters and state variables and is indexed
by ifIndex values of ATM interfaces."
INDEX { ifIndex }
::= { atmInterfaceConfTable 1}
AtmInterfaceConfEntry ::= SEQUENCE {
atmInterfaceMaxVpcs INTEGER,
atmInterfaceMaxVccs INTEGER,
atmInterfaceConfVpcs INTEGER,
atmInterfaceConfVccs INTEGER,
atmInterfaceMaxActiveVpiBits INTEGER,
atmInterfaceMaxActiveVciBits INTEGER,
atmInterfaceIlmiVpi AtmVpIdentifier,
atmInterfaceIlmiVci AtmVcIdentifier,
atmInterfaceAddressType INTEGER,
atmInterfaceAdminAddress AtmAddr,
atmInterfaceMyNeighborIpAddress IpAddress,
atmInterfaceMyNeighborIfName DisplayString,
atmInterfaceCurrentMaxVpiBits INTEGER,
atmInterfaceCurrentMaxVciBits INTEGER,
atmInterfaceSubscrAddress AtmAddr
}
atmInterfaceMaxVpcs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of VPCs (PVPCs and SVPCs)
supported at this ATM interface. At the ATM UNI,
the maximum number of VPCs (PVPCs and SVPCs)
ranges from 0 to 256 only."
::= { atmInterfaceConfEntry 1}
atmInterfaceMaxVccs OBJECT-TYPE
SYNTAX INTEGER (0..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of VCCs (PVCCs and SVCCs)
supported at this ATM interface."
::= { atmInterfaceConfEntry 2}
atmInterfaceConfVpcs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of VPCs (PVPC, Soft PVPC and SVPC)
currently in use at this ATM interface. It includes
the number of PVPCs and Soft PVPCs that are configured
at the interface, plus the number of SVPCs
that are currently established at the
interface.
At the ATM UNI, the configured number of
VPCs (PVPCs and SVPCs) can range from
0 to 256 only."
::= { atmInterfaceConfEntry 3}
atmInterfaceConfVccs OBJECT-TYPE
SYNTAX INTEGER (0..65536)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of VCCs (PVCC, Soft PVCC and SVCC)
currently in use at this ATM interface. It includes
the number of PVCCs and Soft PVCCs that are configured
at the interface, plus the number of SVCCs
that are currently established at the
interface."
::= { atmInterfaceConfEntry 4}
atmInterfaceMaxActiveVpiBits OBJECT-TYPE
SYNTAX INTEGER (0..12)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of active VPI bits
configured for use at the ATM interface.
At the ATM UNI, the maximum number of active
VPI bits configured for use ranges from
0 to 8 only."
::= { atmInterfaceConfEntry 5}
atmInterfaceMaxActiveVciBits OBJECT-TYPE
SYNTAX INTEGER (0..16)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of active VCI bits
configured for use at this ATM interface."
::= { atmInterfaceConfEntry 6}
atmInterfaceIlmiVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VPI value of the VCC supporting
the ILMI at this ATM interface. If the values of
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are
both equal to zero then the ILMI is not
supported at this ATM interface."
DEFVAL { 0 }
::= { atmInterfaceConfEntry 7}
atmInterfaceIlmiVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VCI value of the VCC supporting
the ILMI at this ATM interface. If the values of
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are
both equal to zero then the ILMI is not
supported at this ATM interface."
DEFVAL { 16 }
::= { atmInterfaceConfEntry 8}
atmInterfaceAddressType OBJECT-TYPE
SYNTAX INTEGER {
private(1),
nsapE164(2),
nativeE164(3),
other(4)
}
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The type of primary ATM address configured
for use at this ATM interface."
::= { atmInterfaceConfEntry 9 }
-- The atmInterfaceAdminAddress object has been replaced by
-- atmInterfaceSubscrAddress.
atmInterfaceAdminAddress OBJECT-TYPE
SYNTAX AtmAddr
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The primary address assigned for administrative purposes,
for example, an address associated with the
service provider side of a public network UNI
(thus, the value of this address corresponds
with the value of ifPhysAddress at the host side).
If this interface has no assigned administrative
address, or when the address used for
administrative purposes is the same as that used
for ifPhysAddress, then this is an octet string of
zero length."
::= { atmInterfaceConfEntry 10 }
atmInterfaceMyNeighborIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IP address of the neighbor system connected to
the far end of this interface, to which a Network
Management Station can send SNMP messages, as IP
datagrams sent to UDP port 161, in order to access
network management information concerning the
operation of that system. Note that the value
of this object may be obtained in different ways,
e.g., by manual configuration, or through ILMI
interaction with the neighbor system."
::= { atmInterfaceConfEntry 11 }
atmInterfaceMyNeighborIfName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The textual name of the interface on the neighbor
system on the far end of this interface, and to
which this interface connects. If the neighbor
system is manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface
for this port. If this interface does not have a
textual name, the value of this object is a zero
length string. Note that the value of this object
may be obtained in different ways, e.g., by manual
configuration, or through ILMI interaction with
the neighbor system."
::= { atmInterfaceConfEntry 12 }
atmInterfaceCurrentMaxVpiBits OBJECT-TYPE
SYNTAX INTEGER (0..12)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of VPI Bits that may
currently be used at this ATM interface.
The value is the minimum of
atmInterfaceMaxActiveVpiBits, and the
atmInterfaceMaxActiveVpiBits of the interface's
UNI/NNI peer.
If the interface does not negotiate with
its peer to determine the number of VPI Bits
that can be used on the interface, then the
value of this object must equal
atmInterfaceMaxActiveVpiBits."
::= { atmInterfaceConfEntry 13 }
atmInterfaceCurrentMaxVciBits OBJECT-TYPE
SYNTAX INTEGER (0..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of VCI Bits that may
currently be used at this ATM interface.
The value is the minimum of
atmInterfaceMaxActiveVciBits, and the
atmInterfaceMaxActiveVciBits of the interface's
UNI/NNI peer.
If the interface does not negotiate with
its peer to determine the number of VCI Bits
that can be used on the interface, then the
value of this object must equal
atmInterfaceMaxActiveVciBits."
::= { atmInterfaceConfEntry 14 }
atmInterfaceSubscrAddress OBJECT-TYPE
SYNTAX AtmAddr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The identifier assigned by a service provider
to the network side of a public network UNI.
If this interface has no assigned service provider
address, or for other interfaces this is an octet string
of zero length."
::= { atmInterfaceConfEntry 15 }
-- The ATM Interface DS3 PLCP Table
-- This table contains the DS3 PLCP configuration and
-- state parameters of those ATM interfaces
-- which use DS3 PLCP for carrying ATM cells over DS3.
atmInterfaceDs3PlcpTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceDs3PlcpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface DS3 PLCP
parameters and state variables, one entry per
ATM interface port."
::= { atmMIBObjects 3}
atmInterfaceDs3PlcpEntry OBJECT-TYPE
SYNTAX AtmInterfaceDs3PlcpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains DS3 PLCP parameters and
state variables at the ATM interface and is
indexed by the ifIndex value of the ATM interface."
INDEX { ifIndex }
::= { atmInterfaceDs3PlcpTable 1}
AtmInterfaceDs3PlcpEntry ::= SEQUENCE {
atmInterfaceDs3PlcpSEFSs Counter32,
atmInterfaceDs3PlcpAlarmState INTEGER,
atmInterfaceDs3PlcpUASs Counter32
}
atmInterfaceDs3PlcpSEFSs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of DS3 PLCP Severely Errored Framing
Seconds (SEFS). Each SEFS represents a
one-second interval which contains
one or more SEF events."
::= { atmInterfaceDs3PlcpEntry 1}
atmInterfaceDs3PlcpAlarmState OBJECT-TYPE
SYNTAX INTEGER {
noAlarm(1),
receivedFarEndAlarm(2),
incomingLOF(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if there is an
alarm present for the DS3 PLCP. The value
receivedFarEndAlarm means that the DS3 PLCP
has received an incoming Yellow
Signal, the value incomingLOF means that
the DS3 PLCP has declared a loss of frame (LOF)
failure condition, and the value noAlarm
means that there are no alarms present.
Transition from the failure to the no alarm state
occurs when no defects (e.g., LOF) are received
for more than 10 seconds."
::= { atmInterfaceDs3PlcpEntry 2}
atmInterfaceDs3PlcpUASs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds encountered by the PLCP."
::= { atmInterfaceDs3PlcpEntry 3}
-- The ATM Interface TC Sublayer Table
-- This table contains TC sublayer configuration and
-- state parameters of those ATM interfaces
-- which use TC sublayer for carrying ATM cells over
-- SONET/SDH or DS3.
atmInterfaceTCTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceTCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface TC
Sublayer parameters and state variables,
one entry per ATM interface port."
::= { atmMIBObjects 4}
atmInterfaceTCEntry OBJECT-TYPE
SYNTAX AtmInterfaceTCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains TC Sublayer parameters
and state variables at the ATM interface and is
indexed by the ifIndex value of the ATM interface."
INDEX {ifIndex }
::= { atmInterfaceTCTable 1}
AtmInterfaceTCEntry ::= SEQUENCE {
atmInterfaceOCDEvents Counter32,
atmInterfaceTCAlarmState INTEGER
}
atmInterfaceOCDEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Out of Cell
Delineation (OCD) events occur. If seven
consecutive ATM cells have Header Error
Control (HEC) violations, an OCD event occurs.
A high number of OCD events may indicate a
problem with the TC Sublayer."
::= { atmInterfaceTCEntry 1}
atmInterfaceTCAlarmState OBJECT-TYPE
SYNTAX INTEGER {
noAlarm(1),
lcdFailure(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if there is an
alarm present for the TC Sublayer. The value
lcdFailure(2) indicates that the TC Sublayer
is currently in the Loss of Cell Delineation
(LCD) defect maintenance state. The value
noAlarm(1) indicates that the TC Sublayer
is currently not in the LCD defect
maintenance state."
::= { atmInterfaceTCEntry 2}
-- ATM Traffic Descriptor Parameter Table
-- This table contains a set of self-consistent
-- ATM traffic parameters including the
-- ATM traffic service category.
-- The ATM virtual link tables (i.e., VPL and VCL tables)
-- will use this ATM Traffic Descriptor table
-- to assign traffic parameters and service category
-- to the receive and transmit directions of
-- the ATM virtual links (i.e., VPLs and VCLs).
-- The ATM VPL or VCL table will indicate a row
-- in the atmTrafficDescrParamTable
-- using its atmTrafficDescrParamIndex value.
-- The management application can then compare a set of
-- ATM traffic parameters with a single value.
-- If no suitable row(s) in the atmTrafficDescrParamTable
-- exists, the manager must create a new row(s) in this
-- table. If such a row is created, agent checks the
-- sanity of that set of ATM traffic parameter values.
-- The manager may use atmTrafficDescrParamIndexNext
-- in order to obtain a free atmTrafficDescrParamIndex
-- value.
-- When creating a new row, the parameter values
-- will be checked for self-consistency.
-- Predefined/template rows may be supported.
-- A row in the atmTrafficDescrParamTable is deleted
-- by setting the atmTrafficDescrRowStatus to destroy(6).
-- The agent will check whether this row is still in use
-- by any entry of the atmVplTable or atmVclTable.
-- The agent denies the request if the row is still in
-- use.
-- The ATM Traffic Descriptor Parameter Table
atmTrafficDescrParamTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmTrafficDescrParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on ATM traffic
descriptor type and the associated parameters."
::= { atmMIBObjects 5}
atmTrafficDescrParamEntry OBJECT-TYPE
SYNTAX AtmTrafficDescrParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains ATM traffic descriptor
type and the associated parameters."
INDEX {atmTrafficDescrParamIndex}
::= { atmTrafficDescrParamTable 1}
AtmTrafficDescrParamEntry ::= SEQUENCE {
atmTrafficDescrParamIndex AtmTrafficDescrParamIndex,
atmTrafficDescrType OBJECT IDENTIFIER,
atmTrafficDescrParam1 Integer32,
atmTrafficDescrParam2 Integer32,
atmTrafficDescrParam3 Integer32,
atmTrafficDescrParam4 Integer32,
atmTrafficDescrParam5 Integer32,
atmTrafficQoSClass INTEGER,
atmTrafficDescrRowStatus RowStatus,
atmServiceCategory AtmServiceCategory,
atmTrafficFrameDiscard TruthValue
}
atmTrafficDescrParamIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used by the virtual link
table (i.e., VPL or VCL table)
to identify the row of this table.
When creating a new row in the table
the value of this index may be obtained
by retrieving the value of
atmTrafficDescrParamIndexNext."
::= { atmTrafficDescrParamEntry 1}
atmTrafficDescrType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the type
of ATM traffic descriptor.
The type may indicate no traffic descriptor or
traffic descriptor with one or more parameters.
These parameters are specified as a parameter
vector, in the corresponding instances of the
objects:
atmTrafficDescrParam1
atmTrafficDescrParam2
atmTrafficDescrParam3
atmTrafficDescrParam4
atmTrafficDescrParam5."
DEFVAL { atmNoClpNoScr }
::= { atmTrafficDescrParamEntry 2}
atmTrafficDescrParam1 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 3}
atmTrafficDescrParam2 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The second parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 4}
atmTrafficDescrParam3 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The third parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 5}
atmTrafficDescrParam4 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The fourth parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 6}
atmTrafficDescrParam5 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The fifth parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 7}
atmTrafficQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The value of this object identifies the QoS Class.
Four Service classes have been
specified in the ATM Forum UNI Specification:
Service Class A: Constant bit rate video and
Circuit emulation
Service Class B: Variable bit rate video/audio
Service Class C: Connection-oriented data
Service Class D: Connectionless data
Four QoS classes numbered 1, 2, 3, and 4 have
been specified with the aim to support service
classes A, B, C, and D respectively.
An unspecified QoS Class numbered `0' is used
for best effort traffic."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 8}
atmTrafficDescrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create
a new row or modify or delete an
existing row in this table."
DEFVAL { active }
::= {atmTrafficDescrParamEntry 9}
atmServiceCategory OBJECT-TYPE
SYNTAX AtmServiceCategory
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ATM service category."
DEFVAL { ubr }
::= { atmTrafficDescrParamEntry 10}
atmTrafficFrameDiscard OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If set to 'true', this object indicates that the network
is requested to treat data for this connection, in the
given direction, as frames (e.g. AAL5 CPCS_PDU's) rather
than as individual cells. While the precise
implementation is network-specific, this treatment may
for example involve discarding entire frames during
congestion, rather than a few cells from many frames."
DEFVAL { true }
::= { atmTrafficDescrParamEntry 11 }
-- ATM Interface Virtual Path Link (VPL) Table
-- This table contains configuration and state
-- information of a bi-directional Virtual Path Link
-- (VPL)
-- This table can be used to create, delete or modify
-- a VPL that is terminated in an ATM host or switch.
-- This table can also be used to create, delete or
-- modify a VPL which is cross-connected to another
-- VPL.
-- In the example below, the traffic flows on the receive
-- and transmit directions of the VPLs are characterized
-- by atmVplReceiveTrafficDescrIndex and
-- atmVplTransmitTrafficDescrIndex respectively.
-- The cross-connected VPLs are identified by
-- atmVplCrossConnectIdentifier.
-- ________________________________
-- | |
-- VPL | ATM Host, Switch, or Network | VPL
-- receive | | receive
-- ========> X X <=======
-- <======== X X ========>
-- transmit | | transmit
-- |______________________________|
-- The ATM Interface VPL Table
atmVplTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Virtual Path Link (VPL) table. A
bi-directional VPL is modeled as one entry
in this table. This table can be used for
PVCs, SVCs and Soft PVCs.
Entries are not present in this table for
the VPIs used by entries in the atmVclTable."
::= { atmMIBObjects 6}
atmVplEntry OBJECT-TYPE
SYNTAX AtmVplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the VPL table. This entry is
used to model a bi-directional VPL.
To create a VPL at an ATM interface,
either of the following procedures are used:
Negotiated VPL establishment
(1) The management application creates
a VPL entry in the atmVplTable
by setting atmVplRowStatus to createAndWait(5).
This may fail for the following reasons:
- The selected VPI value is unavailable,
- The selected VPI value is in use.
Otherwise, the agent creates a row and
reserves the VPI value on that port.
(2) The manager selects an existing row(s) in the
atmTrafficDescrParamTable,
thereby, selecting a set of self-consistent
ATM traffic parameters and the service category
for receive and transmit directions of the VPL.
(2a) If no suitable row(s) in the
atmTrafficDescrParamTable exists,
the manager must create a new row(s)
in that table.
(2b) The manager characterizes the VPL's traffic
parameters through setting the
atmVplReceiveTrafficDescrIndex and the
atmVplTransmitTrafficDescrIndex values
in the VPL table, which point to the rows
containing desired ATM traffic parameter values
in the atmTrafficDescrParamTable. The agent
will check the availability of resources and
may refuse the request.
If the transmit and receive service categories
are inconsistent, the agent should refuse the
request.
(3) The manager activates the VPL by setting the
the atmVplRowStatus to active(1).
If this set is successful, the agent has
reserved the resources to satisfy the requested
traffic parameter values and the service category
for that VPL.
(4) If the VPL terminates a VPC in the ATM host
or switch, the manager turns on the
atmVplAdminStatus to up(1) to turn the VPL
traffic flow on. Otherwise, the
atmVpCrossConnectTable must be used
to cross-connect the VPL to another VPL(s)
in an ATM switch or network.
One-Shot VPL Establishment
A VPL may also be established in one step by a
set-request with all necessary VPL parameter
values and atmVplRowStatus set to createAndGo(4).
In contrast to the negotiated VPL establishment
which allows for detailed error checking
(i.e., set errors are explicitly linked to
particular resource acquisition failures),
the one-shot VPL establishment
performs the setup on one operation but
does not have the advantage of step-wise
error checking.
VPL Retirement
A VPL is released by setting atmVplRowStatus to
destroy(6), and the agent may release all
associated resources."
INDEX {ifIndex, atmVplVpi }
::= { atmVplTable 1}
AtmVplEntry ::= SEQUENCE {
atmVplVpi AtmVpIdentifier,
atmVplAdminStatus AtmVorXAdminStatus,
atmVplOperStatus AtmVorXOperStatus,
atmVplLastChange AtmVorXLastChange,
atmVplReceiveTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVplTransmitTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVplCrossConnectIdentifier INTEGER,
atmVplRowStatus RowStatus,
atmVplCastType AtmConnCastType,
atmVplConnKind AtmConnKind
}
atmVplVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of the VPL."
::= { atmVplEntry 1}
atmVplAdminStatus OBJECT-TYPE
SYNTAX AtmVorXAdminStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is instanciated only for a VPL
which terminates a VPC (i.e., one which is
NOT cross-connected to other VPLs).
Its value specifies the desired
administrative state of the VPL."
DEFVAL { down }
::= { atmVplEntry 2}
atmVplOperStatus OBJECT-TYPE
SYNTAX AtmVorXOperStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current operational status of the VPL."
::= { atmVplEntry 3}
atmVplLastChange OBJECT-TYPE
SYNTAX AtmVorXLastChange
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this
VPL entered its current operational state."
::= { atmVplEntry 4 }
atmVplReceiveTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the receive direction of the VPL."
DEFVAL { 0 }
::= { atmVplEntry 5}
atmVplTransmitTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VPL."
DEFVAL { 0 }
::= { atmVplEntry 6}
atmVplCrossConnectIdentifier OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is instantiated only for a VPL
which is cross-connected to other VPLs
that belong to the same VPC. All such
associated VPLs have the same value of this
object, and all their cross-connections are
identified either by entries that are indexed
by the same value of atmVpCrossConnectIndex in
the atmVpCrossConnectTable of this MIB module or by
the same value of the cross-connect index in
the cross-connect table for SVCs and Soft PVCs
(defined in a separate MIB module).
At no time should entries in these respective
cross-connect tables exist simultaneously
with the same cross-connect index value.
The value of this object is initialized by the
agent after the associated entries in the
atmVpCrossConnectTable have been created."
::= {atmVplEntry 7}
atmVplRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, delete
or modify a row in this table.
To create a new VCL, this object is
initially set to 'createAndWait' or
'createAndGo'. This object should not be
set to 'active' unless the following columnar
objects have been set to their desired value
in this row:
atmVplReceiveTrafficDescrIndex and
atmVplTransmitTrafficDescrIndex.
The DESCRIPTION of atmVplEntry provides
further guidance to row treatment in this table."
DEFVAL { createAndWait }
::= {atmVplEntry 8}
atmVplCastType OBJECT-TYPE
SYNTAX AtmConnCastType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The connection topology type."
DEFVAL { p2p }
::= {atmVplEntry 9}
atmVplConnKind OBJECT-TYPE
SYNTAX AtmConnKind
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The use of call control."
DEFVAL { pvc }
::= {atmVplEntry 10}
-- ATM Interface Virtual Channel Link (VCL) Table
-- This table contains configuration and state
-- information of a bi-directional Virtual Channel
-- Link (VCL) at an ATM interface.
-- This table can be used to create, delete or modify
-- a VCL that is terminated in an ATM host or switch.
-- This table can also be
-- used to create, delete or modify a VCL that is
-- cross-connected to another VCL.
-- The ATM Interface VCL Table
atmVclTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Virtual Channel Link (VCL) table. A
bi-directional VCL is modeled as one entry
in this table. This table can be used for
PVCs, SVCs and Soft PVCs."
::= { atmMIBObjects 7}
atmVclEntry OBJECT-TYPE
SYNTAX AtmVclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the VCL table. This entry is
used to model a bi-directional VCL.
To create a VCL at an ATM interface,
either of the following procedures are used:
Negotiated VCL establishment
(1) The management application creates
a VCL entry in the atmVclTable
by setting atmVclRowStatus to createAndWait(5).
This may fail for the following reasons:
- The selected VPI/VCI values are unavailable,
- The selected VPI/VCI values are in use.
Otherwise, the agent creates a row and
reserves the VPI/VCI values on that port.
(2) The manager selects an existing row(s) in the
atmTrafficDescrParamTable,
thereby, selecting a set of self-consistent
ATM traffic parameters and the service category
for receive and transmit directions of the VCL.
(2a) If no suitable row(s) in the
atmTrafficDescrParamTable exists,
the manager must create a new row(s)
in that table.
(2b) The manager characterizes the VCL's traffic
parameters through setting the
atmVclReceiveTrafficDescrIndex and the
atmVclTransmitTrafficDescrIndex values
in the VCL table, which point to the rows
containing desired ATM traffic parameter values
in the atmTrafficDescrParamTable. The agent
will check the availability of resources and
may refuse the request.
If the transmit and receive service categories
are inconsistent, the agent should refuse the
request.
(3) The manager activates the VCL by setting the
the atmVclRowStatus to active(1) (for
requirements on this activation see the
description of atmVclRowStatus).
If this set is successful, the agent has
reserved the resources to satisfy the requested
traffic parameter values and the service category
for that VCL.
(4) If the VCL terminates a VCC in the ATM host
or switch, the manager turns on the
atmVclAdminStatus to up(1) to turn the VCL
traffic flow on. Otherwise, the
atmVcCrossConnectTable must be used
to cross-connect the VCL to another VCL(s)
in an ATM switch or network.
One-Shot VCL Establishment
A VCL may also be established in one step by a
set-request with all necessary VCL parameter
values and atmVclRowStatus set to createAndGo(4).
In contrast to the negotiated VCL establishment
which allows for detailed error checking
(i.e., set errors are explicitly linked to
particular resource acquisition failures),
the one-shot VCL establishment
performs the setup on one operation but
does not have the advantage of step-wise
error checking.
VCL Retirement
A VCL is released by setting atmVclRowStatus to
destroy(6), and the agent may release all
associated resources."
INDEX {ifIndex, atmVclVpi, atmVclVci }
::= { atmVclTable 1}
AtmVclEntry ::= SEQUENCE {
atmVclVpi AtmVpIdentifier,
atmVclVci AtmVcIdentifier,
atmVclAdminStatus AtmVorXAdminStatus,
atmVclOperStatus AtmVorXOperStatus,
atmVclLastChange AtmVorXLastChange,
atmVclReceiveTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVclTransmitTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVccAalType INTEGER,
atmVccAal5CpcsTransmitSduSize INTEGER,
atmVccAal5CpcsReceiveSduSize INTEGER,
atmVccAal5EncapsType INTEGER,
atmVclCrossConnectIdentifier INTEGER,
atmVclRowStatus RowStatus,
atmVclCastType AtmConnCastType,
atmVclConnKind AtmConnKind
}
atmVclVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of the VCL."
::= { atmVclEntry 1}
atmVclVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VCI value of the VCL."
::= { atmVclEntry 2}
atmVclAdminStatus OBJECT-TYPE
SYNTAX AtmVorXAdminStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is instanciated only for a VCL which
terminates a VCC (i.e., one which is NOT
cross-connected to other VCLs). Its value
specifies the desired administrative state of
the VCL."
DEFVAL { down }
::= { atmVclEntry 3}
atmVclOperStatus OBJECT-TYPE
SYNTAX AtmVorXOperStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current operational status of the VCL."
::= { atmVclEntry 4}
atmVclLastChange OBJECT-TYPE
SYNTAX AtmVorXLastChange
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this VCL
entered its current operational state."
::= { atmVclEntry 5 }
atmVclReceiveTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the ATM Traffic Descriptor Table which
applies to the receive direction of this VCL."
DEFVAL { 0 }
::= { atmVclEntry 6}
atmVclTransmitTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
of the ATM Traffic Descriptor Table which applies
to the transmit direction of this VCL."
DEFVAL { 0 }
::= { atmVclEntry 7}
atmVccAalType OBJECT-TYPE
SYNTAX INTEGER {
aal1(1),
aal34(2),
aal5(3),
other(4),
unknown(5),
aal2(6)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL is in use.
The type of AAL used on this VCC.
The AAL type includes AAL1, AAL2, AAL3/4,
and AAL5. The other(4) may be user-defined
AAL type. The unknown type indicates that
the AAL type cannot be determined."
DEFVAL { aal5 }
::= { atmVclEntry 8 }
atmVccAal5CpcsTransmitSduSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The maximum AAL5 CPCS SDU size in octets that is
supported on the transmit direction of this VCC."
DEFVAL { 9188 }
::= { atmVclEntry 9 }
atmVccAal5CpcsReceiveSduSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The maximum AAL5 CPCS SDU size in octets that is
supported on the receive direction of this VCC."
DEFVAL { 9188 }
::= { atmVclEntry 10 }
atmVccAal5EncapsType OBJECT-TYPE
SYNTAX INTEGER {
vcMultiplexRoutedProtocol(1),
vcMultiplexBridgedProtocol8023(2),
vcMultiplexBridgedProtocol8025(3),
vcMultiplexBridgedProtocol8026(4),
vcMultiplexLANemulation8023(5),
vcMultiplexLANemulation8025(6),
llcEncapsulation(7),
multiprotocolFrameRelaySscs(8),
other(9),
unknown(10)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The type of data encapsulation used over
the AAL5 SSCS layer. The definitions reference
RFC 1483 Multiprotocol Encapsulation
over ATM AAL5 and to the ATM Forum
LAN Emulation specification."
DEFVAL { llcEncapsulation }
::= { atmVclEntry 11 }
atmVclCrossConnectIdentifier OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is instantiated only for a VCL
which is cross-connected to other VCLs
that belong to the same VCC. All such
associated VCLs have the same value of this
object, and all their cross-connections are
identified either by entries that are indexed
by the same value of atmVcCrossConnectIndex in
the atmVcCrossConnectTable of this MIB module or by
the same value of the cross-connect index in
the cross-connect table for SVCs and Soft PVCs
(defined in a separate MIB module).
At no time should entries in these respective
cross-connect tables exist simultaneously
with the same cross-connect index value.
The value of this object is initialized by the
agent after the associated entries in the
atmVcCrossConnectTable have been created."
::= {atmVclEntry 12}
atmVclRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, delete or
modify a row in this table. To create
a new VCL, this object is initially set
to 'createAndWait' or 'createAndGo'.
This object should not be
set to 'active' unless the following columnar
objects have been set to their desired value
in this row:
atmVclReceiveTrafficDescrIndex,
atmVclTransmitTrafficDescrIndex.
In addition, if the local VCL end-point
is also the VCC end-point:
atmVccAalType.
In addition, for AAL5 connections only:
atmVccAal5CpcsTransmitSduSize,
atmVccAal5CpcsReceiveSduSize, and
atmVccAal5EncapsType. (The existence
of these objects imply the AAL connection type.).
The DESCRIPTION of atmVclEntry provides
further guidance to row treatment in this table."
DEFVAL { createAndWait }
::= {atmVclEntry 13}
atmVclCastType OBJECT-TYPE
SYNTAX AtmConnCastType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The connection topology type."
DEFVAL { p2p }
::= {atmVclEntry 14}
atmVclConnKind OBJECT-TYPE
SYNTAX AtmConnKind
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The use of call control."
DEFVAL { pvc }
::= {atmVclEntry 15}
-- ATM Virtual Path (VP) Cross Connect Table
-- This table contains configuration and state
-- information of point-to-point,
-- point-to-multipoint, or multipoint-to-multipoint
-- VP cross-connects for PVCs.
-- This table has read-create access and can be used
-- to cross-connect the VPLs together in an ATM switch
-- or network. The atmVpCrossConnectIndex
-- is used to associate the related
-- VPLs that are cross-connected together.
-- The ATM VP Cross Connect Table
-- models each bi-directional VPC
-- cross-connect as a set of entries in
-- the atmVpCrossConnectTable. A
-- point-to-point VPC cross-connect is modeled
-- as one entry; a point-to-multipoint (N leafs) VPC
-- cross-connect as N entries in this table; and
-- a multipoint-to-multipoint (N parties) VPC cross-
-- connect as N(N-1)/2 entries in this table.
-- In the latter cases, all the N (or N(N-1)/2) entries
-- are associated with a single VPC cross-connect by
-- having the same value of atmVpCrossConnectIndex.
-- _________________________________________
-- | |
-- Low | ATM Switch or Network | High
-- port| | port
-- _____|>> from low to high VPC traffic flow >>|______
-- |<< from high to low VPC traffic flow <<|
-- | |
-- |_______________________________________|
--
-- The terms low and high are chosen to represent
-- numerical ordering of the two interfaces associated
-- with a VPC cross-connect. That is, the ATM interface
-- with the lower value of ifIndex is termed 'low',
-- while the other ATM interface associated with the
-- VPC cross-connect is termed 'high'. This terminology
-- is used to provide directional information; for
-- example, the atmVpCrossConnectL2HOperStatus applies
-- to the low->high direction, and
-- atmVpCrossConnectH2LOperStatus applies to the
-- high->low direction, as illustrated above.
atmVpCrossConnectIndexNext OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for atmVpCrossConnectIndex when creating
entries in the atmVpCrossConnectTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmVpCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the current value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index.
After a manager retrieves a value the agent will
determine through its local policy when this index
value will be made available for reuse."
::= { atmMIBObjects 8 }
-- The ATM VP Cross Connect Table
atmVpCrossConnectTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVpCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM VP Cross Connect table for PVCs.
An entry in this table models two
cross-connected VPLs.
Each VPL must have its atmConnKind set
to pvc(1)."
::= { atmMIBObjects 9 }
atmVpCrossConnectEntry OBJECT-TYPE
SYNTAX AtmVpCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the ATM VP Cross Connect table.
This entry is used to model a bi-directional
ATM VP cross-connect which cross-connects
two VPLs.
Step-wise Procedures to set up a VP Cross-connect
Once the entries in the atmVplTable are created,
the following procedures are used
to cross-connect the VPLs together.
(1) The manager obtains a unique
atmVpCrossConnectIndex by reading the
atmVpCrossConnectIndexNext object.
(2) Next, the manager creates a set of one
or more rows in the ATM VP Cross Connect
Table, one for each cross-connection between
two VPLs. Each row is indexed by the ATM
interface port numbers and VPI values of the
two ends of that cross-connection.
This set of rows specifies the topology of the
VPC cross-connect and is identified by a single
value of atmVpCrossConnectIndex.
Negotiated VP Cross-Connect Establishment
(2a) The manager creates a row in this table by
setting atmVpCrossConnectRowStatus to
createAndWait(5). The agent checks the
requested topology and the mutual sanity of
the ATM traffic parameters and
service categories, i.e., the row creation
fails if:
- the requested topology is incompatible with
associated values of atmVplCastType,
- the requested topology is not supported
by the agent,
- the traffic/service category parameter values
associated with the requested row are
incompatible with those of already existing
rows for this VP cross-connect.
[For example, for setting up
a point-to-point VP cross-connect, the
ATM traffic parameters in the receive direction
of a VPL at the low end of the cross-connect
must equal to the traffic parameters in the
transmit direction of the other VPL at the
high end of the cross-connect,
otherwise, the row creation fails.]
The agent also checks for internal errors
in building the cross-connect.
The atmVpCrossConnectIndex values in the
corresponding atmVplTable rows are filled
in by the agent at this point.
(2b) The manager promotes the row in the
atmVpCrossConnectTable by setting
atmVpCrossConnectRowStatus to active(1). If
this set is successful, the agent has reserved
the resources specified by the ATM traffic
parameter and Service category values
for each direction of the VP cross-connect
in an ATM switch or network.
(3) The manager sets the
atmVpCrossConnectAdminStatus to up(1) in all
rows of this VP cross-connect to turn the
traffic flow on.
One-Shot VP Cross-Connect Establishment
A VP cross-connect may also be established in
one step by a set-request with all necessary
parameter values and atmVpCrossConnectRowStatus
set to createAndGo(4).
In contrast to the negotiated VP cross-connect
establishment which allows for detailed error
checking (i.e., set errors are explicitly linked
to particular resource acquisition failures),
the one-shot VP cross-connect establishment
performs the setup on one operation but does not
have the advantage of step-wise error checking.
VP Cross-Connect Retirement
A VP cross-connect identified by a particular
value of atmVpCrossConnectIndex is released by:
(1) Setting atmVpCrossConnectRowStatus of all
rows identified by this value of
atmVpCrossConnectIndex to destroy(6).
The agent may release all
associated resources, and the
atmVpCrossConnectIndex values in the
corresponding atmVplTable row are removed.
Note that a situation when only a subset of
the associated rows are deleted corresponds
to a VP topology change.
(2) After deletion of the appropriate
atmVpCrossConnectEntries, the manager may
set atmVplRowStatus to destroy(6) the
associated VPLs. The agent releases
the resources and removes the associated
rows in the atmVplTable.
VP Cross-connect Reconfiguration
At the discretion of the agent, a VP
cross-connect may be reconfigured by
adding and/or deleting leafs to/from
the VP topology as per the VP cross-connect
establishment/retirement procedures.
Reconfiguration of traffic/service category parameter
values requires release of the VP cross-connect
before those parameter values may by changed
for individual VPLs."
INDEX { atmVpCrossConnectIndex,
atmVpCrossConnectLowIfIndex,
atmVpCrossConnectLowVpi,
atmVpCrossConnectHighIfIndex,
atmVpCrossConnectHighVpi }
::= { atmVpCrossConnectTable 1 }
AtmVpCrossConnectEntry ::= SEQUENCE {
atmVpCrossConnectIndex INTEGER,
atmVpCrossConnectLowIfIndex InterfaceIndex,
atmVpCrossConnectLowVpi AtmVpIdentifier,
atmVpCrossConnectHighIfIndex InterfaceIndex,
atmVpCrossConnectHighVpi AtmVpIdentifier,
atmVpCrossConnectAdminStatus AtmVorXAdminStatus,
atmVpCrossConnectL2HOperStatus AtmVorXOperStatus,
atmVpCrossConnectH2LOperStatus AtmVorXOperStatus,
atmVpCrossConnectL2HLastChange AtmVorXLastChange,
atmVpCrossConnectH2LLastChange AtmVorXLastChange,
atmVpCrossConnectRowStatus RowStatus
}
(next page on part 3)
