RFC 2514
Definitions of Textual Conventions and OBJECT-IDENTITIES for ATM Management
Pages: 20
Proposed Standard
Proposed Standard
Network Working Group M. Noto Request for Comments: 2514 3Com Category: Standards Track E. Spiegel Cisco Systems K. Tesink Bellcore Editors February 1999 Definitions of Textual Conventions and OBJECT-IDENTITIES for ATM Management Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (1999). All Rights Reserved.Table of Contents
1 Introduction .......................................... 2 2 Definitions ........................................... 3 3 Acknowledgments ....................................... 17 4 References ............................................ 17 5 Security Considerations ............................... 17 6 Authors' Addresses .................................... 18 7 Intellectual Property ................................. 19 8 Full Copyright Statement .............................. 20Abstract
This memo describes Textual Conventions and OBJECT-IDENTITIES used for managing ATM-based interfaces, devices, networks and services.1. Introduction
This memo describes Textual Conventions and OBJECT-IDENTITIES used for managing ATM-based interfaces, devices, networks and services.
When designing a MIB module, it is often useful to define new types similar to those defined in the SMI. In comparison to a type defined in the SMI, each of these new types has a different name, a similar syntax, but a more precise semantics. These newly defined types are termed textual conventions, and are used for the convenience of humans reading the MIB module. This is done through Textual Conventions as defined in RFC1903 [1]. It is the purpose of this document to define the set of textual conventions available to ATM MIB modules. When designing MIB modules, it is also often useful to register further properties with object identifier assignments so that they can be further used by other MIB modules. This is done through the OBJECT-IDENTITY macro defined in RFC1902 [2]. This document defines OBJECT-IDENTITIES available to ATM MIB modules. Note that for organizational purposes OBJECT IDENTITIES previously defined in RFC1695 have been moved to this specification and no longer appear in the revision of RFC1695 [3]. However, the original OBJECT IDENTIFIERs have been preserved. For an introduction to the concepts of ATM connections, see [3].2. Definitions
ATM-TC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-IDENTITY, TimeTicks, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; atmTCMIB MODULE-IDENTITY LAST-UPDATED "9810190200Z" ORGANIZATION "IETF AToMMIB Working Group" CONTACT-INFO " Michael Noto Postal: 3Com Corporation 5400 Bayfront Plaza, M/S 3109 Santa Clara, CA 95052 USA Tel: +1 408 326 2218 E-mail: mike_noto@3com.com Ethan Mickey Spiegel
Postal: Cisco Systems
170 W. Tasman Dr.
San Jose, CA 95134
USA
Tel: +1 408 526 6408
E-mail: mspiegel@cisco.com
Kaj Tesink
Postal: Bellcore
331 Newman Springs Road
Red Bank, NJ 07701
USA
Tel: +1 732 758 5254
Fax: +1 732 758 4177
E-mail: kaj@bellcore.com"
DESCRIPTION
"This MIB Module provides Textual Conventions
and OBJECT-IDENTITY Objects to be used by
ATM systems."
::= { mib-2 37 3 } -- atmMIB 3 (see [3])
-- The Textual Conventions defined below are organized
-- alphabetically
AtmAddr ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1x"
STATUS current
DESCRIPTION
"An ATM address. The semantics are implied by
the length. The address types are: - no
address (0 octets) - E.164 (8 octets) - NSAP
(20 octets) In addition, when subaddresses
are used the AtmAddr may represent the
concatenation of address and subaddress. The
associated address types are: - E.164, E.164
(16 octets) - E.164, NSAP (28 octets) - NSAP,
NSAP (40 octets) Address lengths other than
defined in this definition imply address
types defined elsewhere. Note: The E.164
address is encoded in BCD format."
SYNTAX OCTET STRING (SIZE(0..40))
AtmConnCastType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of topology of a connection (point-
to-point, point-to-multipoint). In the case
of point-to-multipoint, the orientation of
this VPL or VCL in the connection.
On a host:
- p2mpRoot indicates that the host
is the root of the p2mp connection.
- p2mpLeaf indicates that the host
is a leaf of the p2mp connection.
On a switch interface:
- p2mpRoot indicates that cells received
by the switching fabric from the interface
are from the root of the p2mp connection.
- p2mpLeaf indicates that cells transmitted
to the interface from the switching fabric
are to the leaf of the p2mp connection."
SYNTAX INTEGER {
p2p(1),
p2mpRoot(2),
p2mpLeaf(3)
}
AtmConnKind ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of call control used for an ATM
connection at a particular interface. The use
is as follows:
pvc(1)
Virtual link of a PVC. Should not be
used for an PVC/SVC (i.e., Soft PVC)
crossconnect.
svcIncoming(2)
Virtual link established after a
received signaling request to setup
an SVC.
svcOutgoing(3)
Virtual link established after a
transmitted or forwarded signaling
request to setup an SVC.
spvcInitiator(4)
Virtual link at the PVC side of an
SVC/PVC crossconnect, where the
switch is the initiator of the Soft PVC
setup.
spvcTarget(5)
Virtual link at the PVC side of an
SVC/PVC crossconnect, where the
switch is the target of the Soft PVC
setup.
For PVCs, a pvc virtual link is always cross-
connected to a pvc virtual link.
For SVCs, an svcIncoming virtual link is always cross-
connected to an svcOutgoing virtual link.
For Soft PVCs, an spvcInitiator is either cross-connected to
an svcOutgoing or an spvcTarget, and an spvcTarget is either
cross-connected to an svcIncoming or an spvcInitiator."
SYNTAX INTEGER {
pvc(1),
svcIncoming(2),
svcOutgoing(3),
spvcInitiator(4),
spvcTarget(5)
}
AtmIlmiNetworkPrefix ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A network prefix used for ILMI address
registration. In the case of ATM endsystem
addresses (AESAs), the network prefix is the first
13 octets of the address which includes the AFI,
IDI, and HO-DSP fields. In the case of native
E.164 addresses, the network prefix is the entire
E.164 address encoded in 8 octets, as if it were
an E.164 IDP in an ATM endsystem address
structure."
REFERENCE
"ATM Forum, Integrated Local Management Interface
(ILMI) Specification, Version 4.0,
af-ilmi-0065.000, September 1996, Section 9
ATM Forum, ATM User-Network Interface Signalling
Specification, Version 4.0 (UNI 4.0),
af-sig-0061.000, June 1996, Section 3"
SYNTAX OCTET STRING (SIZE(8|13))
AtmInterfaceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The connection setup procedures used for the
identified interface.
Other: Connection setup procedures other than
those listed below.
Auto-configuration:
Indicates that the connection setup
procedures are to be determined dynamically,
or that determination has not yet been
completed. One such mechanism is via ATM
Forum ILMI auto-configuration procedures.
ITU-T DSS2:
- ITU-T Recommendation Q.2931, Broadband
Integrated Service Digital Network (B-ISDN)
Digital Subscriber Signalling System No.2
(DSS2) User-Network Interface (UNI) Layer 3
Specification for Basic Call/Connection
Control (September 1994)
- ITU-T Draft Recommendation Q.2961,
B-ISDN DSS 2 Support of Additional Traffic
Parameters (May 1995)
- ITU-T Draft Recommendation Q.2971,
B-ISDN DSS 2 User Network Interface Layer 3
Specification for Point-to-multipoint
Call/connection Control (May 1995)
ATM Forum UNI 3.0:
ATM Forum, ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification,
(1994).
ATM Forum UNI 3.1:
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
(November 1994).
ATM Forum UNI Signalling 4.0:
ATM Forum, ATM User-Network Interface (UNI)
Signalling Specification Version 4.0,
af-sig-0061.000 (June 1996).
ATM Forum IISP (based on UNI 3.0 or UNI 3.1) :
Interim Inter-switch Signaling Protocol
(IISP) Specification, Version 1.0,
af-pnni-0026.000, (December 1994).
ATM Forum PNNI 1.0 :
ATM Forum, Private Network-Network Interface
Specification, Version 1.0, af-pnni-0055.000,
(March 1996).
ATM Forum B-ICI:
ATM Forum, B-ICI Specification, Version 2.0,
af-bici-0013.002, (November 1995).
ATM Forum UNI PVC Only:
An ATM Forum compliant UNI with the
signalling disabled.
ATM Forum NNI PVC Only:
An ATM Forum compliant NNI with the
signalling disabled."
SYNTAX INTEGER {
other(1),
autoConfig(2),
ituDss2(3),
atmfUni3Dot0(4),
atmfUni3Dot1(5),
atmfUni4Dot0(6),
atmfIispUni3Dot0(7),
atmfIispUni3Dot1(8),
atmfIispUni4Dot0(9),
atmfPnni1Dot0(10),
atmfBici2Dot0(11),
atmfUniPvcOnly(12),
atmfNniPvcOnly(13) }
AtmServiceCategory ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The service category for a connection."
REFERENCE
"ATM Forum Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
SYNTAX INTEGER {
other(1), -- none of the following
cbr(2), -- constant bit rate
rtVbr(3), -- real-time variable bit rate
nrtVbr(4), -- non real-time variable bit rate
abr(5), -- available bit rate
ubr(6) -- unspecified bit rate
}
AtmSigDescrParamIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies a row in the
atmSigDescrParamTable. The value 0 signifies that
none of the signalling parameters defined in the
atmSigDescrParamTable are applicable."
SYNTAX INTEGER (0..2147483647)
AtmTrafficDescrParamIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies a row in the
atmTrafficDescrParamTable. The value 0 signifies
that no row has been identified."
SYNTAX INTEGER (0..2147483647)
AtmVcIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The VCI value for a VCL. The maximum VCI value
cannot exceed the value allowable by
atmInterfaceMaxVciBits defined in ATM-MIB."
SYNTAX INTEGER (0..65535)
AtmVpIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The VPI value for a VPL or VCL. The value VPI=0
is only allowed for a VCL. For ATM UNIs supporting
VPCs the VPI value ranges from 0 to 255. The VPI
value 0 is supported for ATM UNIs conforming to
the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs)
specification. For ATM UNIs supporting VCCs the
VPI value ranges from 0 to 255. For ATM NNIs the
VPI value ranges from 0 to 4095. The maximum VPI
value cannot exceed the value allowable by
atmInterfaceMaxVpiBits defined in ATM-MIB."
SYNTAX INTEGER (0..4095)
AtmVorXAdminStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value determines the desired administrative
status of a virtual link or cross-connect. The up
and down states indicate that the traffic flow is
enabled or disabled respectively on the virtual
link or cross-connect."
SYNTAX INTEGER {
up(1),
down(2)
}
AtmVorXLastChange ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime at the time a
virtual link or cross-connect entered its current
operational state. If the current state was
entered prior to the last re-initialization of the
agent then this object contains a zero value."
SYNTAX TimeTicks
AtmVorXOperStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value determines the operational status of a
virtual link or cross-connect. The up and down
states indicate that the traffic flow is enabled
or disabled respectively on the virtual link or
cross-connect. The unknown state indicates that
the state of it cannot be determined. The state
will be down or unknown if the supporting ATM
interface(s) is down or unknown respectively."
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
-- OBJECT-IDENTITIES:
-- The following atmTrafficDescriptorTypes has been moved
-- from RFC1695 and no longer appear in the revision of
-- RFC1695[3].
atmTrafficDescriptorTypes OBJECT IDENTIFIER ::= {mib-2 37 1 1}
-- atmMIBObjects
-- See [3].
-- All other and new OBJECT IDENTITIES
-- are defined under the following subtree:
atmObjectIdentities OBJECT IDENTIFIER ::= {atmTCMIB 1}
-- The following values are defined for use as
-- possible values of the ATM traffic descriptor type.
atmNoTrafficDescriptor OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION
"This identifies the no ATM traffic
descriptor type. Parameters 1, 2, 3, 4,
and 5 are not used. This traffic descriptor
type can be used for best effort traffic."
::= {atmTrafficDescriptorTypes 1}
atmNoClpNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for no CLP
and no Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: not used
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994."
::= {atmTrafficDescriptorTypes 2}
atmClpNoTaggingNoScr OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION
"This traffic descriptor is for CLP without
tagging and no Sustained Cell Rate. The use
of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: peak cell rate in cells/second
for CLP=0 traffic
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= {atmTrafficDescriptorTypes 3}
atmClpTaggingNoScr OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION
"This traffic descriptor is for CLP with
tagging and no Sustained Cell Rate. The use
of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: peak cell rate in cells/second
for CLP=0 traffic, excess
tagged as CLP=1
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= {atmTrafficDescriptorTypes 4}
atmNoClpScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for no CLP
with Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0+1 traffic
Parameter 3: maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994."
::= {atmTrafficDescriptorTypes 5}
atmClpNoTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for CLP with
Sustained Cell Rate and no tagging. The use
of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0 traffic
Parameter 3: maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994."
::= {atmTrafficDescriptorTypes 6}
atmClpTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for CLP with
tagging and Sustained Cell Rate. The use of
the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0 traffic, excess tagged as
CLP=1
Parameter 3: maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994."
::= {atmTrafficDescriptorTypes 7}
atmClpNoTaggingMcr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for CLP with
Minimum Cell Rate and no tagging. The use of
the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: CDVT in tenths of microseconds
Parameter 3: minimum cell rate in cells/second
Parameter 4: unused
Parameter 5: unused."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994."
::= {atmTrafficDescriptorTypes 8}
atmClpTransparentNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for the CLP-
transparent model and no Sustained Cell Rate.
The use of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: CDVT in tenths of microseconds
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor type is applicable to
connections following the CBR.1 conformance
definition.
Connections specifying this traffic descriptor
type will be rejected at UNI 3.0 or UNI 3.1
interfaces. For a similar traffic descriptor
type that can be accepted at UNI 3.0 and
UNI 3.1 interfaces, see atmNoClpNoScr."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 9}
atmClpTransparentScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for the CLP-
transparent model with Sustained Cell Rate.
The use of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0+1 traffic
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in tenths of microseconds
Parameter 5: not used.
This traffic descriptor type is applicable to
connections following the VBR.1 conformance
definition.
Connections specifying this traffic descriptor
type will be rejected at UNI 3.0 or UNI 3.1
interfaces. For a similar traffic descriptor
type that can be accepted at UNI 3.0 and
UNI 3.1 interfaces, see atmNoClpScr."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 10}
atmNoClpTaggingNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for no CLP
with tagging and no Sustained Cell Rate. The
use of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: CDVT in tenths of microseconds
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor type is applicable to
connections following the UBR.2 conformance
definition ."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 11}
atmNoClpNoScrCdvt OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for no CLP
and no Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: CDVT in tenths of microseconds
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor type is applicable to
CBR connections following the UNI 3.0/3.1
conformance definition for PCR CLP=0+1.
These CBR connections differ from CBR.1
connections in that the CLR objective
applies only to the CLP=0 cell flow.
This traffic descriptor type is also
applicable to connections following the UBR.1
conformance definition."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 12}
atmNoClpScrCdvt OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for no CLP
with Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0+1 traffic
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in tenths of microseconds
Parameter 5: not used.
This traffic descriptor type is applicable
to VBR connections following the UNI 3.0/3.1
conformance definition for PCR CLP=0+1 and
SCR CLP=0+1. These VBR connections
differ from VBR.1 connections in that
the CLR objective applies only to the CLP=0
cell flow."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 13}
atmClpNoTaggingScrCdvt OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for CLP with
Sustained Cell Rate and no tagging. The use
of the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0 traffic
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in tenths of microseconds
Parameter 5: not used.
This traffic descriptor type is applicable to
connections following the VBR.2 conformance
definition."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 14}
atmClpTaggingScrCdvt OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor type is for CLP with
tagging and Sustained Cell Rate. The use of
the parameter vector for this type:
Parameter 1: peak cell rate in cells/second
for CLP=0+1 traffic
Parameter 2: sustainable cell rate in cells/second
for CLP=0 traffic, excess tagged as
CLP=1
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in tenths of microseconds
Parameter 5: not used.
This traffic descriptor type is applicable to
connections following the VBR.3 conformance
definition."
REFERENCE
"ATM Forum,ATM User-Network Interface,
Version 3.0 (UNI 3.0) Specification, 1994.
ATM Forum, ATM User-Network Interface,
Version 3.1 (UNI 3.1) Specification,
November 1994.
ATM Forum, Traffic Management Specification,
Version 4.0, af-tm-0056.000, June 1996."
::= {atmTrafficDescriptorTypes 15}
END
3. Acknowledgments
This document is a product of the AToMMIB Working Group.
4. References
[1] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Textual Conventions for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1903, January 1996.
[2] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Structure
of Management Information for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1902, January 1996.
[3] Tesink, K., Editor, "Definitions of Managed Objects for ATM
Management", RFC 2515, February 1999.
5. Security Considerations
This memo defines textual conventions and object identities for use
in ATM MIB modules. Security issues for these MIB modules are
addressed in the memos defining those modules.
6. Authors' Addresses
Michael Noto 3Com Corporation 5400 Bayfront Plaza, M/S 3109 Santa Clara, CA 95052 Phone +1 408 326 2218 Email: mike_noto@3com.com Ethan Mickey Spiegel Cisco Systems 170 W. Tasman Dr. San Jose, CA 95134 USA Phone +1 408 526 6408 EMail: mspiegel@cisco.com Kaj Tesink Bellcore 331 Newman Springs Road P.O. Box 7020 Red Bank, NJ 07701-7020 Phone: (732) 758-5254 EMail: kaj@bellcore.com
7. Intellectual Property
The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.
8. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.