RFC 1382
SNMP MIB Extension for the X.25 Packet Layer
Pages: 69
Proposed Standard
Proposed Standard
Part 2 of 3 – Pages 7 to 39
4. Object Definitions RFC1382-MIB DEFINITIONS ::= BEGIN IMPORTS Counter, Gauge, TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString, transmission FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215 EntryStatus FROM RFC1271-MIB PositiveInteger, IfIndexType FROM RFC1381-MIB; x25 OBJECT IDENTIFIER ::= { transmission 5 } -- Support of the X25 subtree and all subtrees under it -- is mandatory for all agents of system that implement X.25. X121Address ::= OCTET STRING (SIZE(0..17)) -- 0 to 17 bytes in length containing the ASCII -- characters [0-9], each octet contains one digit -- of the address. -- ########################################################### -- X.25 Administration Table -- ########################################################### x25AdmnTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25AdmnEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains the administratively
set configuration parameters for an X.25
Packet Level Entity (PLE).
Most of the objects in this table have
corresponding objects in the x25OperTable.
This table contains the values as last set
by the administrator. The x25OperTable
contains the values actually in use by an
X.25 PLE.
Changing an administrative value may or may
not change a current operating value. The
operating value may not change until the
interface is restarted. Some
implementations may change the values
immediately upon changing the administrative
table. All implementations are required to
load the values from the administrative
table when initializing a PLE."
::= { x25 1 }
x25AdmnEntry OBJECT-TYPE
SYNTAX X25AdmnEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25AdmnTable."
INDEX { x25AdmnIndex }
::= { x25AdmnTable 1 }
X25AdmnEntry ::= SEQUENCE {
x25AdmnIndex
IfIndexType,
x25AdmnInterfaceMode
INTEGER,
x25AdmnMaxActiveCircuits
INTEGER,
x25AdmnPacketSequencing
INTEGER,
x25AdmnRestartTimer
PositiveInteger,
x25AdmnCallTimer
PositiveInteger,
x25AdmnResetTimer
PositiveInteger,
x25AdmnClearTimer
PositiveInteger,
x25AdmnWindowTimer
PositiveInteger,
x25AdmnDataRxmtTimer
PositiveInteger,
x25AdmnInterruptTimer
PositiveInteger,
x25AdmnRejectTimer
PositiveInteger,
x25AdmnRegistrationRequestTimer
PositiveInteger,
x25AdmnMinimumRecallTimer
PositiveInteger,
x25AdmnRestartCount
INTEGER,
x25AdmnResetCount
INTEGER,
x25AdmnClearCount
INTEGER,
x25AdmnDataRxmtCount
INTEGER,
x25AdmnRejectCount
INTEGER,
x25AdmnRegistrationRequestCount
INTEGER,
x25AdmnNumberPVCs
INTEGER,
x25AdmnDefCallParamId
OBJECT IDENTIFIER,
x25AdmnLocalAddress
X121Address,
x25AdmnProtocolVersionSupported
OBJECT IDENTIFIER
}
x25AdmnIndex OBJECT-TYPE
SYNTAX IfIndexType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the X.25 Interface."
::= { x25AdmnEntry 1 }
x25AdmnInterfaceMode OBJECT-TYPE
SYNTAX INTEGER {
dte (1),
dce (2),
dxe (3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Identifies DCE/DTE mode in which the
interface operates. A value of dxe
indicates the mode will be determined by XID
negotiation."
REFERENCE "10733 5.9 interfaceMode"
::= { x25AdmnEntry 2 }
x25AdmnMaxActiveCircuits OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum number of circuits this PLE can
support; including PVCs."
REFERENCE "10733 5.9 maxActiveCircuits;
See ISO 8208, Section 3.7"
::= { x25AdmnEntry 3 }
x25AdmnPacketSequencing OBJECT-TYPE
SYNTAX INTEGER {
modulo8 (1),
modulo128 (2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The modulus of the packet sequence number
space."
REFERENCE "10733 extendedPacketSequencing;
See ISO 8208 Section 7.1.1"
::= { x25AdmnEntry 4 }
x25AdmnRestartTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T20 restart timer in milliseconds."
REFERENCE "10733 5.9 restartTime
See ISO 8208 Section 4.1, table 26"
::= { x25AdmnEntry 5 }
x25AdmnCallTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T21 Call timer in milliseconds."
REFERENCE "10733 callTime;
See ISO 8208 Section 5.2.1, table 26"
::= { x25AdmnEntry 6 }
x25AdmnResetTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T22 Reset timer in milliseconds."
REFERENCE "10733 resetTime;
See ISO 8208 Section 8.1, table 26"
::= { x25AdmnEntry 7 }
x25AdmnClearTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T23 Clear timer in milliseconds."
REFERENCE "10733 clearTime;
See ISO 8208 Section 5.5.1, table 26"
::= { x25AdmnEntry 8 }
x25AdmnWindowTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T24 window status transmission timer in
milliseconds. A value of 2147483647
indicates no window timer in use."
REFERENCE "10733 5.10.1 windowTime (opt);
See ISO 8208 Section 11.2.2, table 26"
::= { x25AdmnEntry 9 }
x25AdmnDataRxmtTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T25 data retransmission timer in
milliseconds. A value of 2147483647
indicates no data retransmission timer in
use."
REFERENCE "10733 5.10.1 dataRetransmissionTime (opt);
See ISO 8208 Section 11.2.1, table 26"
::= { x25AdmnEntry 10 }
x25AdmnInterruptTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T26 interrupt timer in milliseconds. A
value of 2147483647 indicates no interrupt
timer in use."
REFERENCE "10733 interruptTime;
See ISO 8208 Section 6.8.1, table 26"
::= { x25AdmnEntry 11 }
x25AdmnRejectTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T27 Reject retransmission timer in
milliseconds. A value of 2147483647
indicates no reject timer in use."
REFERENCE "10733 5.10.1 dataRejectTime (opt);
See ISO 8208 Section 13.4.1, table 26"
::= { x25AdmnEntry 12 }
x25AdmnRegistrationRequestTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The T28 registration timer in milliseconds.
A value of 2147483647 indicates no
registration timer in use."
REFERENCE "10733 5.8.1 registrationRequestTime (opt)
See ISO 8208 Section 13.1.1.1, table 26"
::= { x25AdmnEntry 13 }
x25AdmnMinimumRecallTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Minimum time interval between unsuccessful
call attempts in milliseconds."
REFERENCE "10733 5.9 minimum RecallTimer"
::= { x25AdmnEntry 14 }
x25AdmnRestartCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The R20 restart retransmission count."
REFERENCE "10733 5.9 restartCount;
See ISO 8208 Section 4.1, table 27"
::= { x25AdmnEntry 15 }
x25AdmnResetCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The r22 Reset retransmission count."
REFERENCE "10733 resetCount;
See section ISO 8208 8.1, table 27"
::= { x25AdmnEntry 16 }
x25AdmnClearCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The r23 Clear retransmission count."
REFERENCE "10733 clearCount;
See ISO 8208 Section 5.5.1, table 27"
::= { x25AdmnEntry 17 }
x25AdmnDataRxmtCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The R25 Data retransmission count. This
value is irrelevant if the
x25AdmnDataRxmtTimer indicates no timer in
use."
REFERENCE "10733 5.10.1 dataRetransmissionCount (opt)
See ISO 8208 Section 11.2.1, table 27"
::= { x25AdmnEntry 18 }
x25AdmnRejectCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The R27 reject retransmission count. This
value is irrelevant if the
x25AdmnRejectTimer indicates no timer in
use."
REFERENCE "10733 5.10.1 dataRejectCount (opt)"
::= { x25AdmnEntry 19 }
x25AdmnRegistrationRequestCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The R28 Registration retransmission Count.
This value is irrelevant if the
x25AdmnRegistrationRequestTimer indicates no
timer in use."
REFERENCE "10733 5.8.1 registrationRequestCount (opt);
See ISO 8208 Section 13.1.1.1, table 27"
::= { x25AdmnEntry 20 }
x25AdmnNumberPVCs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of PVC configured for this PLE.
The PVCs use channel numbers from 1 to this
number."
::= { x25AdmnEntry 21 }
x25AdmnDefCallParamId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This identifies the instance of the
x25CallParmIndex for the entry in the
x25CallParmTable which contains the default
call parameters for this PLE."
::= { x25AdmnEntry 22 }
x25AdmnLocalAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The local address for this PLE subnetwork.
A zero length address maybe returned by PLEs
that only support PVCs."
REFERENCE "10733 5.9 localDTEAddress"
::= { x25AdmnEntry 23 }
x25AdmnProtocolVersionSupported OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Identifies the version of the X.25 protocol
this interface should support. Object
identifiers for common versions are defined
below in the x25ProtocolVersion subtree."
REFERENCE "10733 5.9 protocolVersionSupported"
::= { x25AdmnEntry 24 }
-- ###########################################################
-- X.25 Operational Table
-- ###########################################################
x25OperTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25OperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The operation parameters in use by the X.25
PLE."
::= { x25 2 }
x25OperEntry OBJECT-TYPE
SYNTAX X25OperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25OperTable."
INDEX { x25OperIndex }
::= { x25OperTable 1 }
X25OperEntry ::= SEQUENCE {
x25OperIndex
IfIndexType,
x25OperInterfaceMode
INTEGER,
x25OperMaxActiveCircuits
INTEGER,
x25OperPacketSequencing
INTEGER,
x25OperRestartTimer
PositiveInteger,
x25OperCallTimer
PositiveInteger,
x25OperResetTimer
PositiveInteger,
x25OperClearTimer
PositiveInteger,
x25OperWindowTimer
PositiveInteger,
x25OperDataRxmtTimer
PositiveInteger,
x25OperInterruptTimer
PositiveInteger,
x25OperRejectTimer
PositiveInteger,
x25OperRegistrationRequestTimer
PositiveInteger,
x25OperMinimumRecallTimer
PositiveInteger,
x25OperRestartCount
INTEGER,
x25OperResetCount
INTEGER,
x25OperClearCount
INTEGER,
x25OperDataRxmtCount
INTEGER,
x25OperRejectCount
INTEGER,
x25OperRegistrationRequestCount
INTEGER,
x25OperNumberPVCs
INTEGER,
x25OperDefCallParamId
OBJECT IDENTIFIER,
x25OperLocalAddress
X121Address,
x25OperDataLinkId
OBJECT IDENTIFIER,
x25OperProtocolVersionSupported
OBJECT IDENTIFIER
}
x25OperIndex OBJECT-TYPE
SYNTAX IfIndexType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the X.25 interface."
::= { x25OperEntry 1 }
x25OperInterfaceMode OBJECT-TYPE
SYNTAX INTEGER {
dte (1),
dce (2),
dxe (3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Identifies DCE/DTE mode in which the
interface operates. A value of dxe
indicates the role will be determined by XID
negotiation at the Link Layer and that
negotiation has not yet taken place."
REFERENCE "10733 5.9 interfaceMode"
::= { x25OperEntry 2 }
x25OperMaxActiveCircuits OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of circuits this PLE can
support."
REFERENCE "10733 5.9 maxActiveCircuits
See ISO 8208, Section 3.7"
::= { x25OperEntry 3 }
x25OperPacketSequencing OBJECT-TYPE
SYNTAX INTEGER {
modulo8 (1),
modulo128 (2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The modulus of the packet sequence number
space."
REFERENCE "10733 extendedPacketSequencing;
See ISO 8208 Section 7.1.1"
::= { x25OperEntry 4 }
x25OperRestartTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T20 restart timer in milliseconds."
REFERENCE "10733 5.9 restartTime;
See ISO 8208 Section 4.1, table 26"
::= { x25OperEntry 5 }
x25OperCallTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T21 Call timer in milliseconds."
REFERENCE "10733 callTime;
See ISO 8208 Section 5.2.1, table 26"
::= { x25OperEntry 6 }
x25OperResetTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T22 Reset timer in milliseconds."
REFERENCE "10733 resetTime;
See ISO 8208 Section 8.1, table 26"
::= { x25OperEntry 7 }
x25OperClearTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T23 Clear timer in milliseconds."
REFERENCE "10733 clearTime;
See ISO 8208 Section 5.5.1, table 26"
::= { x25OperEntry 8 }
x25OperWindowTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T24 window status transmission timer
milliseconds. A value of 2147483647
indicates no window timer in use."
REFERENCE "10733 5.10.1 windowTime (opt);
See ISO 8208 Section 11.2.2, table 26"
::= { x25OperEntry 9 }
x25OperDataRxmtTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T25 Data Retransmission timer in
milliseconds. A value of 2147483647
indicates no data retransmission timer in
use."
REFERENCE "10733 5.10.1 dataRetransmissionTime (opt);
See ISO 8208 Section 11.2.1, table 26"
::= { x25OperEntry 10 }
x25OperInterruptTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T26 Interrupt timer in milliseconds. A
value of 2147483647 indicates interrupts are
not being used."
REFERENCE "10733 interruptTime;
See ISO 8208 Section 6.8.1, table 26"
::= { x25OperEntry 11 }
x25OperRejectTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T27 Reject retransmission timer in
milliseconds. A value of 2147483647
indicates no reject timer in use."
REFERENCE "10733 5.10.1 dataRejectTime (opt);
See ISO 8208 Section 13.4.1, table 26"
::= { x25OperEntry 12 }
x25OperRegistrationRequestTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The T28 registration timer in milliseconds.
A value of 2147483647 indicates no
registration timer in use."
REFERENCE "10733 5.8.1 registrationRequestTime (opt);
See ISO 8208 Section 13.1.1.1, table 26"
::= { x25OperEntry 13 }
x25OperMinimumRecallTimer OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Minimum time interval between unsuccessful
call attempts in milliseconds."
REFERENCE "10733 5.9 minimum RecallTimer"
::= { x25OperEntry 14 }
x25OperRestartCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The R20 restart retransmission count."
REFERENCE "10733 5.9 restartCount
See ISO 8208 Section 4.1, table 27"
::= { x25OperEntry 15 }
x25OperResetCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The r22 Reset retransmission count."
REFERENCE "10733 resetCount;
See section ISO 8208 8.1, table 27"
::= { x25OperEntry 16 }
x25OperClearCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The r23 Clear retransmission count."
REFERENCE "10733 clearCount;
See ISO 8208 Section 5.5.1, table 27"
::= { x25OperEntry 17 }
x25OperDataRxmtCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The R25 Data retransmission count. This
value is undefined if the
x25OperDataRxmtTimer indicates no timer in
use."
REFERENCE "10733 5.10.1 dataRetransmissionCount (opt);
See ISO 8208 Section 11.2.1, table 27"
::= { x25OperEntry 18 }
x25OperRejectCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The R27 reject retransmission count. This
value is undefined if the x25OperRejectTimer
indicates no timer in use."
REFERENCE "10733 5.10.1 dataRejectCount (opt)"
::= { x25OperEntry 19 }
x25OperRegistrationRequestCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The R28 Registration retransmission Count.
This value is undefined if the
x25OperREgistrationRequestTimer indicates no
timer in use."
REFERENCE "10733 5.8.1 registrationRequestCount (opt);
See ISO 8208 Section 13.1.1.1, table 27"
::= { x25OperEntry 20 }
x25OperNumberPVCs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PVC configured for this PLE.
The PVCs use channel numbers from 1 to this
number."
::= { x25OperEntry 21 }
x25OperDefCallParamId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This identifies the instance of the
x25CallParmIndex for the entry in the
x25CallParmTable that contains the default
call parameters for this PLE."
::= { x25OperEntry 22 }
x25OperLocalAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The local address for this PLE subnetwork.
A zero length address maybe returned by PLEs
that only support PVCs."
REFERENCE "10733 5.9 localDTEAddress"
::= { x25OperEntry 23 }
x25OperDataLinkId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This identifies the instance of the index
object in the first table of the most device
specific MIB for the interface used by this
PLE."
::= { x25OperEntry 24 }
x25OperProtocolVersionSupported OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Identifies the version of the X.25 protocol
this interface supports. Object identifiers
for common versions are defined below in the
x25ProtocolVersion subtree."
REFERENCE "10733 5.9 protocolVersionSupported"
::= { x25OperEntry 25 }
-- MIB-II also provides:
-- ifDescr:
-- On an X.25 interface this must include sufficient
-- information to enable the system's administrator
-- to determine the appropriate configuration
-- information on a system having multiple X.25
-- subnetworks.
-- ifType: ddn-x25 or rfc877-x25
-- an interface of type ddn-x25 will use an algorithm to
-- translate between X.121 address and IP addresses.
-- An interface of type rfc877-x25 will use a
-- configuration table to translate between X.121
-- addresses and IP addresses.
-- ifMtu: the maximum PDU a higher layer can pass to X.25 or
-- receive from X.25
-- ifSpeed:
-- This will be the value of the local clock for this line.
-- A value of zero indicates external clocking.
-- ifAdminStatus:
-- ifOperStatus
-- ifLastChange
-- ###########################################################
-- X.25 Statistics Table
-- ###########################################################
x25StatTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25StatEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Statistics information about this X.25
PLE."
::= { x25 3 }
x25StatEntry OBJECT-TYPE
SYNTAX X25StatEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of the x25StatTable."
INDEX { x25StatIndex }
::= { x25StatTable 1 }
X25StatEntry ::= SEQUENCE {
x25StatIndex
IfIndexType,
x25StatInCalls
Counter,
x25StatInCallRefusals
Counter,
x25StatInProviderInitiatedClears
Counter,
x25StatInRemotelyInitiatedResets
Counter,
x25StatInProviderInitiatedResets
Counter,
x25StatInRestarts
Counter,
x25StatInDataPackets
Counter,
x25StatInAccusedOfProtocolErrors
Counter,
x25StatInInterrupts
Counter,
x25StatOutCallAttempts
Counter,
x25StatOutCallFailures
Counter,
x25StatOutInterrupts
Counter,
x25StatOutDataPackets
Counter,
x25StatOutgoingCircuits
Gauge,
x25StatIncomingCircuits
Gauge,
x25StatTwowayCircuits
Gauge,
x25StatRestartTimeouts
Counter,
x25StatCallTimeouts
Counter,
x25StatResetTimeouts
Counter,
x25StatClearTimeouts
Counter,
x25StatDataRxmtTimeouts
Counter,
x25StatInterruptTimeouts
Counter,
x25StatRetryCountExceededs
Counter,
x25StatClearCountExceededs
Counter
}
x25StatIndex OBJECT-TYPE
SYNTAX IfIndexType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the X.25 interface."
::= { x25StatEntry 1 }
x25StatInCalls OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of incoming calls received."
::= { x25StatEntry 2 }
x25StatInCallRefusals OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of incoming calls refused. This
includes calls refused by the PLE and by
higher layers. This also includes calls
cleared because of restricted fast select."
::= { x25StatEntry 3 }
x25StatInProviderInitiatedClears OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of clear requests with a cause
code other than DTE initiated."
REFERENCE "10733 providerInitiatedDisconnect"
::= { x25StatEntry 4 }
x25StatInRemotelyInitiatedResets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of reset requests received with
cause code DTE initiated."
REFERENCE "10733 remotelyInitiatedResets"
::= { x25StatEntry 5 }
x25StatInProviderInitiatedResets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of reset requests received with
cause code other than DTE initiated."
REFERENCE "10733 ProviderInitiatedResets"
::= { x25StatEntry 6 }
x25StatInRestarts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of remotely initiated (including
provider initiated) restarts experienced by
the PLE excluding the restart associated
with bringing up the PLE interface. This
only counts restarts received when the PLE
already has an established connection with
the remove PLE."
REFERENCE "10733 5.9 remotelyInitiatedRestarts"
::= { x25StatEntry 7 }
x25StatInDataPackets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data packets received."
REFERENCE "10733 5.9 dataPacketsReceived."
::= { x25StatEntry 8 }
x25StatInAccusedOfProtocolErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets received containing a
procedure error cause code. These include
clear, reset, restart, or diagnostic
packets."
REFERENCE "CD 10733 5.9 accusedOfProtocolError"
::= { x25StatEntry 9 }
x25StatInInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets received by
the PLE or over the PVC/VC."
REFERENCE "10733 interruptPacketsReceived"
::= { x25StatEntry 10 }
x25StatOutCallAttempts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of calls attempted."
REFERENCE "10733 5.9 callAttempts"
::= { x25StatEntry 11 }
x25StatOutCallFailures OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of call attempts which failed.
This includes calls that were cleared
because of restrictive fast select."
::= { x25StatEntry 12 }
x25StatOutInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets send by the
PLE or over the PVC/VC."
REFERENCE "10733 InterruptPacketsSent"
::= { x25StatEntry 13 }
x25StatOutDataPackets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data packets sent by this
PLE."
REFERENCE "10733 dataPacketSent"
::= { x25StatEntry 14 }
x25StatOutgoingCircuits OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of active outgoing circuits.
This includes call requests sent but not yet
confirmed. This does not count PVCs."
::= { x25StatEntry 15 }
x25StatIncomingCircuits OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of active Incoming Circuits.
This includes call indications received but
not yet acknowledged. This does not count
PVCs."
::= { x25StatEntry 16 }
x25StatTwowayCircuits OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of active two-way Circuits.
This includes call requests sent but not yet
confirmed. This does not count PVCs."
::= { x25StatEntry 17 }
x25StatRestartTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T20 restart timer
expired."
REFERENCE "10733 5.9 restartTimeouts"
::= { x25StatEntry 18 }
x25StatCallTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T21 call timer
expired."
REFERENCE "10733 5.9 callTimeouts"
::= { x25StatEntry 19 }
x25StatResetTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T22 reset timer
expired."
REFERENCE "10733 5.9 resetTimeouts"
::= { x25StatEntry 20 }
x25StatClearTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T23 clear timer
expired."
REFERENCE "10733 5.9 clearTimeouts"
::= { x25StatEntry 21 }
x25StatDataRxmtTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T25 data timer
expired."
REFERENCE "10733 5.9 dataRetransmissionsTimerExpiries"
::= { x25StatEntry 22 }
x25StatInterruptTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T26 interrupt timer
expired."
REFERENCE "10733 5.9 interruptTimerExpires"
::= { x25StatEntry 23 }
x25StatRetryCountExceededs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times a retry counter was
exhausted."
REFERENCE "10733 5.9 retryCountsExceeded"
::= { x25StatEntry 24 }
x25StatClearCountExceededs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the R23 clear count was
exceeded."
REFERENCE "10733 5.9 clearCountsExceeded"
::= { x25StatEntry 25 }
-- MIB-II also contains:
-- ifInOctets: Number of data octets delivered to upper
-- layer entities.
-- ifInUcastPkts: Number of packets with a clear M-bit
-- delivered to higher layer entities.
-- ifDiscards: Number of packets dropped for lack of buffering
-- ifInErrors: Number of packets received containing errors
-- REFERENCE ProtocolErrorsDetectedLocally
-- ifInUnknownProtos: Number of packets with unknown circuit
-- identifier.
-- ifOutOctets: Number of data octets delivered by
-- X.25 to upper layers.
-- ifOutUcastPkts: Number of packets with a clear M-bit
-- received from higher layer entities.
-- ###########################################################
-- X.25 Channel Table
-- ###########################################################
x25ChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25ChannelEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These objects contain information about the
channel number configuration in an X.25 PLE.
These values are the configured values.
changes in these values after the interfaces
has started may not be reflected in the
operating PLE."
REFERENCE "See ISO 8208, Section 3.7"
::= { x25 4 }
x25ChannelEntry OBJECT-TYPE
SYNTAX X25ChannelEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25ChannelTable."
REFERENCE "This provides the information available
in 10733 logicalChannelAssignments."
INDEX { x25ChannelIndex }
::= { x25ChannelTable 1 }
X25ChannelEntry ::= SEQUENCE {
x25ChannelIndex
IfIndexType,
x25ChannelLIC
INTEGER,
x25ChannelHIC
INTEGER,
x25ChannelLTC
INTEGER,
x25ChannelHTC
INTEGER,
x25ChannelLOC
INTEGER,
x25ChannelHOC
INTEGER
}
x25ChannelIndex OBJECT-TYPE
SYNTAX IfIndexType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the X.25 Interface."
::= { x25ChannelEntry 1 }
x25ChannelLIC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Incoming channel."
::= { x25ChannelEntry 2 }
x25ChannelHIC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Incoming channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 3 }
x25ChannelLTC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Two-way channel."
::= { x25ChannelEntry 4 }
x25ChannelHTC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Two-way channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 5 }
x25ChannelLOC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest outgoing channel."
::= { x25ChannelEntry 6 }
x25ChannelHOC OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest outgoing channel. A value of zero
indicates no channels in this range."
::= { x25ChannelEntry 7 }
-- ###########################################################
-- X25 Per Circuits Information Table
-- ###########################################################
x25CircuitTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25CircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"These objects contain general information
about a specific circuit of an X.25 PLE."
::= { x25 5 }
x25CircuitEntry OBJECT-TYPE
SYNTAX X25CircuitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries of x25CircuitTable."
INDEX { x25CircuitIndex,
x25CircuitChannel }
::= { x25CircuitTable 1 }
X25CircuitEntry ::= SEQUENCE {
x25CircuitIndex
IfIndexType,
x25CircuitChannel
INTEGER,
x25CircuitStatus
INTEGER,
x25CircuitEstablishTime
TimeTicks,
x25CircuitDirection
INTEGER,
x25CircuitInOctets
Counter,
x25CircuitInPdus
Counter,
x25CircuitInRemotelyInitiatedResets
Counter,
x25CircuitInProviderInitiatedResets
Counter,
x25CircuitInInterrupts
Counter,
x25CircuitOutOctets
Counter,
x25CircuitOutPdus
Counter,
x25CircuitOutInterrupts
Counter,
x25CircuitDataRetransmissionTimeouts
Counter,
x25CircuitResetTimeouts
Counter,
x25CircuitInterruptTimeouts
Counter,
x25CircuitCallParamId
OBJECT IDENTIFIER,
x25CircuitCalledDteAddress
X121Address,
x25CircuitCallingDteAddress
X121Address,
x25CircuitOriginallyCalledAddress
X121Address,
x25CircuitDescr
DisplayString
}
x25CircuitIndex OBJECT-TYPE
SYNTAX IfIndexType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the X.25 Interface."
::= { x25CircuitEntry 1 }
x25CircuitChannel OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The channel number for this circuit."
::= { x25CircuitEntry 2 }
x25CircuitStatus OBJECT-TYPE
SYNTAX INTEGER { -- state table states
invalid (1),
closed (2), -- (p1)
calling (3), -- (p2,p3,p5)
open (4), -- (p4)
clearing (5), -- (p6,p7)
pvc (6),
pvcResetting (7),
startClear (8), -- Close cmd
startPvcResetting (9), -- Reset cmd
other (10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object reports the current status of
the circuit.
An existing instance of this object can only
be set to startClear, startPvcResetting, or
invalid. An instance with the value calling
or open can only be set to startClear and
that action will start clearing the circuit.
An instance with the value PVC can only be
set to startPvcResetting or invalid and that
action resets the PVC or deletes the circuit
respectively. The values startClear or
startPvcResetting will never be returned by
an agent. An attempt to set the status of
an existing instance to a value other than
one of these values will result in an error.
A non-existing instance can be set to PVC to
create a PVC if the implementation supports
dynamic creation of PVCs. Some
implementations may only allow creation and
deletion of PVCs if the interface is down.
Since the instance identifier will supply
the PLE index and the channel number,
setting this object alone supplies
sufficient information to create the
instance. All the DEFVAL clauses for the
other objects of this table are appropriate
for creating a PVC; PLEs creating entries
for placed or accepted calls will use values
appropriate for the call rather than the
value of the DEFVAL clause. Two managers
trying to create the same PVC can determine
from the return code which manager succeeded
and which failed (the failing manager fails
because it can not set a value of PVC for an
existing object).
An entry in the closed or invalid state may
be deleted or reused at the agent's
convence. If the entry is kept in the
closed state, the values of the parameters
associated with the entry must be correct.
Closed implies the values in the circuit
table are correct.
The value of invalid indicates the other
values in the table are invalid. Many
agents may never return a value of invalid
because they dynamically allocate and free
unused table entries. An agent for a
statically configured systems can return
invalid to indicate the entry has not yet
been used so the counters contain no
information."
REFERENCE "See ISO 8208,
table 33 for (p<n>) state table"
::= { x25CircuitEntry 3 }
x25CircuitEstablishTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the channel was
associated with this circuit. For outgoing
SVCs, this is the time the first call packet
was sent. For incoming SVCs, this is the
time the call indication was received. For
PVCs this is the time the PVC was able to
pass data to a higher layer entity without
loss of data."
::= { x25CircuitEntry 4 }
x25CircuitDirection OBJECT-TYPE
SYNTAX INTEGER {
incoming (1),
outgoing (2),
pvc (3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The direction of the call that established
this circuit."
REFERENCE "10733 direction"
DEFVAL { pvc }
::= { x25CircuitEntry 5 }
-- X25 Circuit data flow statistics
x25CircuitInOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets of user data delivered
to upper layer."
REFERENCE "5.11 octetsReceivedCounter"
::= { x25CircuitEntry 6 }
x25CircuitInPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs received for this
circuit."
REFERENCE "10733 5.11 dataPacketsReceived"
::= { x25CircuitEntry 7 }
x25CircuitInRemotelyInitiatedResets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Resets received for this
circuit with cause code of DTE initiated."
REFERENCE "10733 remotelyInitiatedResets"
::= { x25CircuitEntry 8 }
x25CircuitInProviderInitiatedResets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Resets received for this
circuit with cause code other than DTE
initiated."
REFERENCE "10733 ProviderInitiatedResets"
::= { x25CircuitEntry 9 }
x25CircuitInInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets received
for this circuit."
REFERENCE "10733 interruptPacketsReceived"
::= { x25CircuitEntry 10 }
x25CircuitOutOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets of user data sent for
this circuit."
REFERENCE "10733 5.11 octetsSentCounter"
::= { x25CircuitEntry 11 }
x25CircuitOutPdus OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PDUs sent for this circuit."
REFERENCE "10733 5.11 dataPacketsSent"
::= { x25CircuitEntry 12 }
x25CircuitOutInterrupts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of interrupt packets sent on
this circuit."
REFERENCE "10733 interruptPacketsSent"
::= { x25CircuitEntry 13 }
-- X25 circuit timer statistics
x25CircuitDataRetransmissionTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T25 data
retransmission timer expired for this
circuit."
REFERENCE "10733 5.11 dataRetransmissionTimerExpiries"
::= { x25CircuitEntry 14 }
x25CircuitResetTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T22 reset timer
expired for this circuit."
REFERENCE "10733 5.11 resetTimeouts"
::= { x25CircuitEntry 15 }
x25CircuitInterruptTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of times the T26 Interrupt timer
expired for this circuit."
REFERENCE "10733 interruptTimerExpiries"
::= { x25CircuitEntry 16 }
x25CircuitCallParamId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This identifies the instance of the
x25CallParmIndex for the entry in the
x25CallParmTable which contains the call
parameters in use with this circuit. The
entry referenced must contain the values
that are currently in use by the circuit
rather than proposed values. A value of
NULL indicates the circuit is a PVC or is
using all the default parameters."
DEFVAL { {0 0} }
::= { x25CircuitEntry 17 }
x25CircuitCalledDteAddress OBJECT-TYPE
SYNTAX X121Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"For incoming calls, this is the called
address from the call indication packet.
For outgoing calls, this is the called
(next page on part 3)