RFC 4327
Link Management Protocol (LMP) Management Information Base (MIB)
9. LMP MIB Module Definitions
This MIB module IMPORTs objects from [RFC2578], [RFC2579], [RFC2580], [RFC2863], [RFC4001], and [RFC4220], and it has REFERENCE clauses to [RFC4204], [RFC4207], [RFC4209], [RFC3471], and [RFC2914]. LMP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, transmission, Unsigned32, Counter32, TimeTicks FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC -- [RFC2579] InterfaceIndexOrZero, ifIndex FROM IF-MIB -- [RFC2863] InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] teLinkRemoteIpAddr, teLinkIncomingIfId, TeLinkEncodingType FROM TE-LINK-STD-MIB; -- [RFC4220] lmpMIB MODULE-IDENTITY LAST-UPDATED "200601110000Z" -- 11 January 2006 ORGANIZATION "Common Control and Measurement Protocols (CCAMP) Working Group" CONTACT-INFO " Martin Dubuc Email: dubuc.consulting@sympatico.ca Thomas D. Nadeau Email: tnadeau@cisco.com Jonathan P. Lang Email: jplang@ieee.org Evan McGinnis Email: emcginnis@hammerheadsystems.com" DESCRIPTION
"Copyright (C) 2006 The Internet Society. This version of
the MIB module is part of RFC 4327; see the RFC itself
for full legal notices.
This MIB module contains managed object definitions for
the Link Management Protocol (LMP) as
defined in 'Link Management Protocol'."
-- Revision history.
REVISION
"200601110000Z" -- 11 January 2006
DESCRIPTION
"Initial version published as RFC 4327"
::= { transmission 227 }
-- Textual Conventions
LmpInterval ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The interval delay in milliseconds."
SYNTAX Unsigned32 (1..65535)
LmpRetransmitInterval ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The retransmission interval delay in milliseconds."
SYNTAX Unsigned32 (1..4294967295)
LmpNodeId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1d.1d.1d.1d"
STATUS current
DESCRIPTION
"Represents a Node ID in network byte order. Node ID is an
address of type IPv4."
REFERENCE
"Section 1.1 of Link Management Protocol, RFC 4204"
SYNTAX OCTET STRING(SIZE(4))
-- Top level components of this MIB
-- Notifications
lmpNotifications OBJECT IDENTIFIER ::= { lmpMIB 0 }
-- Tables, Scalars
lmpObjects OBJECT IDENTIFIER ::= { lmpMIB 1 }
-- Conformance
lmpConformance OBJECT IDENTIFIER ::= { lmpMIB 2 }
lmpAdminStatus OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired operational status of LMP on the node.
Implementations should save the value of this object in
persistent memory so that it survives restarts or reboot."
DEFVAL { up }
::= { lmpObjects 1 }
lmpOperStatus OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual operational status of LMP on the node."
::= { lmpObjects 2 }
-- LMP Neighbor Table
lmpNbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the neighbor node(s) to which control
channels may be established."
::= { lmpObjects 3 }
lmpNbrEntry OBJECT-TYPE
SYNTAX LmpNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by a LMP-enabled device for
every pair of nodes that can establish control channels."
INDEX { lmpNbrNodeId }
::= { lmpNbrTable 1 }
LmpNbrEntry ::= SEQUENCE {
lmpNbrNodeId LmpNodeId,
lmpNbrRetransmitInterval LmpRetransmitInterval,
lmpNbrRetryLimit Unsigned32,
lmpNbrRetransmitDelta Unsigned32,
lmpNbrAdminStatus INTEGER,
lmpNbrOperStatus INTEGER,
lmpNbrRowStatus RowStatus,
lmpNbrStorageType StorageType
}
lmpNbrNodeId OBJECT-TYPE
SYNTAX LmpNodeId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is a unique index for an entry in the LmpNbrTable.
This value represents the remote Node ID."
::= { lmpNbrEntry 1 }
lmpNbrRetransmitInterval OBJECT-TYPE
SYNTAX LmpRetransmitInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the initial retransmission interval that
is used for the retransmission of messages that require
acknowledgement. This object along with lmpNbrRetryLimit is
used to implement congestion-handling mechanism as defined in
Section 10 of the Link Management Protocol specification,
which is based on RFC 2914."
REFERENCE
"Link Management Protocol, RFC 4204.
Congestion Control Principles, RFC 2914."
DEFVAL { 500 }
::= { lmpNbrEntry 2 }
lmpNbrRetryLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the maximum number of times a message
is transmitted without being acknowledged. A value of 0 is used
to indicate that a node should never stop retransmission.
This object along with lmpNbrRetransmitInterval is
used to implement congestion-handling mechanism as defined in
Section 10 of the Link Management Protocol specification,
which is based on RFC 2914."
REFERENCE
"Link Management Protocol, RFC 4204.
Congestion Control Principles, RFC 2914."
DEFVAL { 3 }
::= { lmpNbrEntry 3 }
lmpNbrRetransmitDelta OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object governs the speed with which the sender increases
the retransmission interval as explained in section 10 of the
Link Management Protocol specification, which is based on
RFC 2914. This value is a power used to express the
exponential backoff. The ratio of two successive retransmission
intervals is (1 + Delta)."
REFERENCE
"Link Management Protocol, RFC 4204.
Congestion Control Principles, RFC 2914."
DEFVAL { 1 }
::= { lmpNbrEntry 4 }
lmpNbrAdminStatus OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The desired operational status of LMP to this remote node."
::= { lmpNbrEntry 5 }
lmpNbrOperStatus OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual operational status of LMP to this remote node."
::= { lmpNbrEntry 6 }
lmpNbrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. None of the writable objects
in a row can be changed if the status is active(1).
All read-create objects must have valid and consistent
values before the row can be activated."
::= { lmpNbrEntry 7 }
lmpNbrStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
lmpNbrTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row."
DEFVAL { nonVolatile }
::= { lmpNbrEntry 8 }
-- End of lmpNbrTable
lmpCcHelloIntervalDefault OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default value for the HelloInterval
parameter used in the Hello protocol keep-alive phase. It
indicates how frequently LMP Hello messages will be sent. It
is used a the default value for lmpCcHelloInterval.
Implementations should save the value of this object in
persistent memory so that it survives restarts or reboot."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpObjects 4 }
lmpCcHelloIntervalDefaultMin OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default minimum value for the
HelloInterval parameter. It is used as a default value
for lmpCcHelloIntervalMin. Implementations should save the
value of this object in persistent memory so that it survives
restarts or reboot."
::= { lmpObjects 5 }
lmpCcHelloIntervalDefaultMax OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default maximum value for the
HelloInterval parameter. It is used as a default value
for lmpCcHelloIntervalMax. Implementations should save the
value of this object in persistent memory so that it survives
restarts or reboot."
::= { lmpObjects 6 }
lmpCcHelloDeadIntervalDefault OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default HelloDeadInterval parameter
to use in the Hello protocol keep-alive phase. It indicates
how long a device should wait before declaring the control
channel dead. The HelloDeadInterval parameter should be at
least three times the value of HelloInterval. It is used as
a default value for lmpCcHelloDeadInterval. Implementations
should save the value of this object in persistent memory so
that it survives restarts or reboot."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpObjects 7 }
lmpCcHelloDeadIntervalDefaultMin OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default minimum value for the
HelloDeadInterval parameter. It is used as a default value
for lmpCcHelloDeadIntervalMin. Implementations should save
the value of this object in persistent memory so that it
survives restarts or reboot."
::= { lmpObjects 8 }
lmpCcHelloDeadIntervalDefaultMax OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default maximum value for the
HelloDeadInterval parameter. It is used as a default value
for lmpCcHelloDeadIntervalMax. Implementations should save the
value of this object in persistent memory so that it survives
restarts or reboot."
::= { lmpObjects 9 }
-- LMP Control Channel Table
lmpControlChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpControlChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies LMP control channel information."
::= { lmpObjects 10 }
lmpControlChannelEntry OBJECT-TYPE
SYNTAX LmpControlChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by a LMP-enabled device for
every control channel. Whenever a new entry is created with
lmpCcIsIf set to true(2), then a corresponding entry is
created in ifTable as well (see RFC 2863)."
INDEX { lmpCcId }
::= { lmpControlChannelTable 1 }
LmpControlChannelEntry ::= SEQUENCE {
lmpCcId Unsigned32,
lmpCcUnderlyingIfIndex InterfaceIndexOrZero,
lmpCcIsIf TruthValue,
lmpCcNbrNodeId LmpNodeId,
lmpCcRemoteId Unsigned32,
lmpCcRemoteAddressType InetAddressType,
lmpCcRemoteIpAddr InetAddress,
lmpCcSetupRole INTEGER,
lmpCcAuthentication TruthValue,
lmpCcHelloInterval LmpInterval,
lmpCcHelloIntervalMin LmpInterval,
lmpCcHelloIntervalMax LmpInterval,
lmpCcHelloIntervalNegotiated LmpInterval,
lmpCcHelloDeadInterval LmpInterval,
lmpCcHelloDeadIntervalMin LmpInterval,
lmpCcHelloDeadIntervalMax LmpInterval,
lmpCcHelloDeadIntervalNegotiated LmpInterval,
lmpCcLastChange TimeTicks,
lmpCcAdminStatus INTEGER,
lmpCcOperStatus INTEGER,
lmpCcRowStatus RowStatus,
lmpCcStorageType StorageType
}
lmpCcId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value represents the local control channel identifier.
The control channel identifier is a non-zero 32-bit number."
::= { lmpControlChannelEntry 1 }
lmpCcUnderlyingIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If lmpCcIsIf is set to true(1), this object carries the
index into the ifTable of the entry that represents the
LMP interface over which LMP will transmit its traffic.
If this object is set to zero, but lmpCcIsIf is set to
true(1), the control channel is not currently associated
with any underlying interface and the control channel's
operational status must not be up(1), nor should the
control channel forward or receive traffic.
If lmpCcIsIf is set to false(2), this object should be set
to zero and should be ignored."
::= { lmpControlChannelEntry 2 }
lmpCcIsIf OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"In implementations where the control channels are modeled
as interfaces, the value of this object is true(1) and
this control channel is represented by an interface in
the interfaces group table as indicated by the value of
lmpCcUnderlyingIfIndex. If control channels are not
modeled as interfaces, the value of this object is
false(2) and there is no corresponding interface for
this control channel in the interfaces group table,
and the value of lmpCcUnderlyingIfIndex should be
ignored."
::= { lmpControlChannelEntry 3 }
lmpCcNbrNodeId OBJECT-TYPE
SYNTAX LmpNodeId
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the Node ID of the control channel remote node.
This value either is configured or gets created by the node
when a Config message is received or when an outgoing Config
message is acknowledged by the remote node."
::= { lmpControlChannelEntry 4 }
lmpCcRemoteId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the remote control channel identifier
(32-bit number). It is determined during the negotiation
phase. A value of zero means that the remote control channel
identifier has not yet been learnt."
::= { lmpControlChannelEntry 5 }
lmpCcRemoteAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents the remote control channel IP address
type. In point-to-point configuration, this value can be set
to unknown(0)."
::= { lmpControlChannelEntry 6 }
lmpCcRemoteIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents the remote control channel Internet
address for numbered control channel. The type of this
address is determined by lmpCcRemoteAddressType.
Control channel must be numbered on non-point-to-point
configuration. For point-to-point configuration, the
remote control channel address can be of type unknown
in which case this object must be a zero-length string. The
lmpCcRemoteId object then identifies the unnumbered
address."
::= { lmpControlChannelEntry 7 }
lmpCcSetupRole OBJECT-TYPE
SYNTAX INTEGER { active(1), passive(2) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The role that this node should take during establishment
of this control channel. An active node will initiate
establishment. A passive node will wait for the remote node
to initiate. A pair of nodes that both take the passive role
will never establish communications."
DEFVAL { active }
::= { lmpControlChannelEntry 8 }
lmpCcAuthentication OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates whether the control channel must use
authentication."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpControlChannelEntry 9 }
lmpCcHelloInterval OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the value of the HelloInterval
parameter. The default value for this object should be
set to lmpCcHelloIntervalDefault."
::= { lmpControlChannelEntry 10 }
lmpCcHelloIntervalMin OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum value for the
HelloInterval parameter. The default value for this
object should be set to lmpCcHelloIntervalMinDefault."
::= { lmpControlChannelEntry 11 }
lmpCcHelloIntervalMax OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the maximum value for the
HelloInterval parameter. The default value for this
object should be set to lmpCcHelloIntervalMaxDefault."
::= { lmpControlChannelEntry 12 }
lmpCcHelloIntervalNegotiated OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Once the control channel is active, this object represents
the negotiated HelloInterval value."
::= { lmpControlChannelEntry 13 }
lmpCcHelloDeadInterval OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the value of the HelloDeadInterval
parameter. The default value for this object should be
set to lmpCcHelloDeadIntervalDefault."
::= { lmpControlChannelEntry 14 }
lmpCcHelloDeadIntervalMin OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum value for the
HelloDeadInterval parameter. The default value for this
object should be set to lmpCcHelloDeadIntervalMinDefault."
::= { lmpControlChannelEntry 15 }
lmpCcHelloDeadIntervalMax OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the maximum value for the
HelloDeadInterval parameter. The default value for this
object should be set to lmpCcHelloIntervalMaxDefault."
::= { lmpControlChannelEntry 16 }
lmpCcHelloDeadIntervalNegotiated OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Once the control channel is active, this object represents
the negotiated HelloDeadInterval value."
::= { lmpControlChannelEntry 17 }
lmpCcLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the control channel entered
its current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains a
zero value."
::= { lmpControlChannelEntry 18 }
lmpCcAdminStatus OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The desired operational status of this control channel."
::= { lmpControlChannelEntry 19 }
lmpCcOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
configSnd(3),
configRcv(4),
active(5),
goingDown(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual operational status of this control channel."
::= { lmpControlChannelEntry 20 }
lmpCcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. None of the writable objects
in a row can be changed if the status is active(1).
All read-create objects must have valid and consistent
values before the row can be activated."
::= { lmpControlChannelEntry 21 }
lmpCcStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
lmpControlChannelTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row."
DEFVAL { nonVolatile }
::= { lmpControlChannelEntry 22 }
-- End of lmpControlChannelTable
-- LMP Control Channel Performance Table
lmpControlChannelPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpControlChannelPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies LMP control channel performance
counters."
::= { lmpObjects 11 }
lmpControlChannelPerfEntry OBJECT-TYPE
SYNTAX LmpControlChannelPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by a LMP-enabled device for
every control channel. lmpCcCounterDiscontinuityTime is used
to indicate potential discontinuity for all counter objects
in this table."
INDEX { lmpCcId }
::= { lmpControlChannelPerfTable 1 }
LmpControlChannelPerfEntry ::= SEQUENCE {
lmpCcInOctets Counter32,
lmpCcInDiscards Counter32,
lmpCcInErrors Counter32,
lmpCcOutOctets Counter32,
lmpCcOutDiscards Counter32,
lmpCcOutErrors Counter32,
lmpCcConfigReceived Counter32, lmpCcConfigSent Counter32, lmpCcConfigRetransmit Counter32, lmpCcConfigAckReceived Counter32, lmpCcConfigAckSent Counter32, lmpCcConfigNackReceived Counter32, lmpCcConfigNackSent Counter32, lmpCcHelloReceived Counter32, lmpCcHelloSent Counter32, lmpCcBeginVerifyReceived Counter32, lmpCcBeginVerifySent Counter32, lmpCcBeginVerifyRetransmit Counter32, lmpCcBeginVerifyAckReceived Counter32, lmpCcBeginVerifyAckSent Counter32, lmpCcBeginVerifyNackReceived Counter32, lmpCcBeginVerifyNackSent Counter32, lmpCcEndVerifyReceived Counter32, lmpCcEndVerifySent Counter32, lmpCcEndVerifyRetransmit Counter32, lmpCcEndVerifyAckReceived Counter32, lmpCcEndVerifyAckSent Counter32, lmpCcTestStatusSuccessReceived Counter32, lmpCcTestStatusSuccessSent Counter32, lmpCcTestStatusSuccessRetransmit Counter32, lmpCcTestStatusFailureReceived Counter32, lmpCcTestStatusFailureSent Counter32, lmpCcTestStatusFailureRetransmit Counter32, lmpCcTestStatusAckReceived Counter32, lmpCcTestStatusAckSent Counter32, lmpCcLinkSummaryReceived Counter32, lmpCcLinkSummarySent Counter32, lmpCcLinkSummaryRetransmit Counter32, lmpCcLinkSummaryAckReceived Counter32, lmpCcLinkSummaryAckSent Counter32, lmpCcLinkSummaryNackReceived Counter32, lmpCcLinkSummaryNackSent Counter32, lmpCcChannelStatusReceived Counter32, lmpCcChannelStatusSent Counter32, lmpCcChannelStatusRetransmit Counter32, lmpCcChannelStatusAckReceived Counter32, lmpCcChannelStatusAckSent Counter32, lmpCcChannelStatusReqReceived Counter32, lmpCcChannelStatusReqSent Counter32, lmpCcChannelStatusReqRetransmit Counter32, lmpCcChannelStatusRspReceived Counter32, lmpCcChannelStatusRspSent Counter32, lmpCcCounterDiscontinuityTime TimeStamp }
lmpCcInOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of LMP message octets received on the
control channel."
::= { lmpControlChannelPerfEntry 1 }
lmpCcInDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of inbound packets that were chosen to be
discarded even though no errors had been detected. One
possible reason for discarding such a packet could be to
free up buffer space."
::= { lmpControlChannelPerfEntry 2 }
lmpCcInErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of inbound packets that contained errors
preventing them from being processed by LMP."
::= { lmpControlChannelPerfEntry 3 }
lmpCcOutOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of LMP message octets transmitted out of
the control channel."
::= { lmpControlChannelPerfEntry 4 }
lmpCcOutDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of outbound packets that were chosen to be
discarded even though no errors had been detected to
prevent their being transmitted. One possible reason
for discarding such a packet could be to free up buffer
space."
::= { lmpControlChannelPerfEntry 5 }
lmpCcOutErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of outbound packets that could not be
transmitted because of errors."
::= { lmpControlChannelPerfEntry 6 }
lmpCcConfigReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Config messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 7 }
lmpCcConfigSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Config messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 8 }
lmpCcConfigRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Config messages that
have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 9 }
lmpCcConfigAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ConfigAck messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 10 }
lmpCcConfigAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ConfigAck messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 11 }
lmpCcConfigNackReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ConfigNack messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 12 }
lmpCcConfigNackSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ConfigNack messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 13 }
lmpCcHelloReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Hello messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 14 }
lmpCcHelloSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Hello messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 15 }
lmpCcBeginVerifyReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 16 }
lmpCcBeginVerifySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 17 }
lmpCcBeginVerifyRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that
have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 18 }
lmpCcBeginVerifyAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyAck messages that
have been received on this control channel."
::= { lmpControlChannelPerfEntry 19 }
lmpCcBeginVerifyAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyAck messages that
have been sent on this control channel."
::= { lmpControlChannelPerfEntry 20 }
lmpCcBeginVerifyNackReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyNack messages that
have been received on this control channel."
::= { lmpControlChannelPerfEntry 21 }
lmpCcBeginVerifyNackSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyNack messages that
have been sent on this control channel."
::= { lmpControlChannelPerfEntry 22 }
lmpCcEndVerifyReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that have
been received on this control channel."
::= { lmpControlChannelPerfEntry 23 }
lmpCcEndVerifySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that have
been sent on this control channel."
::= { lmpControlChannelPerfEntry 24 }
lmpCcEndVerifyRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that
have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 25 }
lmpCcEndVerifyAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerifyAck messages that
have been received on this control channel."
::= { lmpControlChannelPerfEntry 26 }
lmpCcEndVerifyAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerifyAck messages that
have been sent on this control channel."
::= { lmpControlChannelPerfEntry 27 }
lmpCcTestStatusSuccessReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 28 }
lmpCcTestStatusSuccessSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 29 }
lmpCcTestStatusSuccessRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 30 }
lmpCcTestStatusFailureReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 31 }
lmpCcTestStatusFailureSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 32 }
lmpCcTestStatusFailureRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 33 }
lmpCcTestStatusAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusAck messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 34 }
lmpCcTestStatusAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusAck messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 35 }
lmpCcLinkSummaryReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 36 }
lmpCcLinkSummarySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 37 }
lmpCcLinkSummaryRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages that
have been retransmitted over this control channel."
::= { lmpControlChannelPerfEntry 38 }
lmpCcLinkSummaryAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryAck messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 39 }
lmpCcLinkSummaryAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryAck messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 40 }
lmpCcLinkSummaryNackReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryNack messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 41 }
lmpCcLinkSummaryNackSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryNack messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 42 }
lmpCcChannelStatusReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 43 }
lmpCcChannelStatusSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 44 }
lmpCcChannelStatusRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages
that have been retransmitted on this control channel."
::= { lmpControlChannelPerfEntry 45 }
lmpCcChannelStatusAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusAck messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 46 }
lmpCcChannelStatusAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 47 }
lmpCcChannelStatusReqReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusRequest messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 48 }
lmpCcChannelStatusReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusRequest messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 49 }
lmpCcChannelStatusReqRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusRequest messages
that have been retransmitted on this control channel."
::= { lmpControlChannelPerfEntry 50 }
lmpCcChannelStatusRspReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusResponse messages
that have been received on this control channel."
::= { lmpControlChannelPerfEntry 51 }
lmpCcChannelStatusRspSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusResponse messages
that have been sent on this control channel."
::= { lmpControlChannelPerfEntry 52 }
lmpCcCounterDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
any one or more of this control channel's counters suffered a
discontinuity. The relevant counters are the specific
instances associated with this control channel of any
Counter32 object contained in the lmpControlChannelPerfTable.
If no such discontinuities have occurred since the last re-
initialization of the local management subsystem, then this
object contains a zero value."
::= { lmpControlChannelPerfEntry 53 }
-- End of lmpControlChannelPerfTable
-- LMP TE Link Table
lmpTeLinkTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpTeLinkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the LMP-specific TE link information.
Overall TE link information is kept in three separate tables:
ifTable for interface-specific information, lmpTeLinkTable
for LMP specific information, and teLinkTable for generic
TE link information. ifIndex is the common index to all
tables."
::= { lmpObjects 12 }
lmpTeLinkEntry OBJECT-TYPE
SYNTAX LmpTeLinkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table exists for each ifEntry with an
ifType of teLink(200) that is managed by LMP. An ifEntry with
an ifIndex must exist before the corresponding lmpTeLinkEntry is
created. If a TE link entry in the ifTable is destroyed, then
so is the corresponding entry in the lmpTeLinkTable. The
administrative status value is controlled from the ifEntry.
Setting the administrative status to testing prompts LMP to
start link verification on the TE link. Information about the
TE link that is not LMP specific is contained in teLinkTable of
the TE-LINK-STD-MIB MIB module."
INDEX { ifIndex }
::= { lmpTeLinkTable 1 }
LmpTeLinkEntry ::= SEQUENCE {
lmpTeLinkNbrRemoteNodeId LmpNodeId,
lmpTeLinkVerification TruthValue,
lmpTeLinkFaultManagement TruthValue,
lmpTeLinkDwdm TruthValue,
lmpTeLinkOperStatus INTEGER,
lmpTeLinkRowStatus RowStatus,
lmpTeLinkStorageType StorageType
}
lmpTeLinkNbrRemoteNodeId OBJECT-TYPE
SYNTAX LmpNodeId
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the Node ID of the TE link remote node. This value
may be learned during control channel parameter negotiation
phase (in the Config message). Node ID is an address whose
type must be IPv4."
::= { lmpTeLinkEntry 1 }
lmpTeLinkVerification OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates if the LMP link verification procedure
is enabled for this TE link."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpTeLinkEntry 2 }
lmpTeLinkFaultManagement OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates if the LMP fault management procedure
is enabled on this TE link."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpTeLinkEntry 3 }
lmpTeLinkDwdm OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates if the LMP DWDM procedure is enabled
on this TE link."
REFERENCE
"Link Management Protocol (LMP) for Dense Wavelength Division
Multiplexing (DWDM) Optical Line Systems, RFC 4209"
::= { lmpTeLinkEntry 4 }
lmpTeLinkOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1), down(2), testing(3), init(4), degraded(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual operational status of this TE link. The status
is set to testing when the TE link is performing link
verification. A degraded state indicates that there is
no active control channel between the pair of nodes that
form the endpoints of the TE link, but yet at least one
data-bearing link on the TE link is allocated."
::= { lmpTeLinkEntry 5 }
lmpTeLinkRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. None of the writable objects
in a row can be changed if the status is active(1).
All read-create objects must have valid and consistent
values before the row can be activated."
::= { lmpTeLinkEntry 6 }
lmpTeLinkStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
lmpTeLinkTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row."
DEFVAL { nonVolatile }
::= { lmpTeLinkEntry 7 }
-- End of lmpTeLinkTable
lmpGlobalLinkVerificationInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates how often the link verification
procedure is executed. The interval is in milliseconds.
A value of 0 is used to indicate that the link
verification procedure should not be executed. The
interval specified in this object should be large enough
to allow the verification procedure to be completed
before the start of the next interval.
Implementations should save the value of this object in
persistent memory so that it survives restarts or reboot."
::= { lmpObjects 13 }
-- LMP Link Verification Table
lmpLinkVerificationTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpLinkVerificationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies TE link information associated with the
LMP verification procedure."
::= { lmpObjects 14 }
lmpLinkVerificationEntry OBJECT-TYPE
SYNTAX LmpLinkVerificationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by an LMP-enabled device for
every TE link that supports the LMP verification
procedure."
INDEX { ifIndex }
::= { lmpLinkVerificationTable 1 }
LmpLinkVerificationEntry ::= SEQUENCE {
lmpLinkVerifyInterval LmpInterval,
lmpLinkVerifyDeadInterval LmpInterval,
lmpLinkVerifyTransportMechanism BITS,
lmpLinkVerifyAllLinks TruthValue,
lmpLinkVerifyTransmissionRate Unsigned32,
lmpLinkVerifyWavelength Unsigned32,
lmpLinkVerifyRowStatus RowStatus,
lmpLinkVerifyStorageType StorageType
}
lmpLinkVerifyInterval OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the VerifyInterval parameter used
in the LMP link verification process. It indicates the
interval at which the Test messages are sent."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpLinkVerificationEntry 1 }
lmpLinkVerifyDeadInterval OBJECT-TYPE
SYNTAX LmpInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the VerifyDeadInterval parameter used
in the verification of the physical connectivity of data-
bearing links. It specifies the observation period used to
detect a Test message at the remote node."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpLinkVerificationEntry 2 }
lmpLinkVerifyTransportMechanism OBJECT-TYPE
SYNTAX BITS {
-- All encoding types:
payload(0),
-- SONET/SDH encoding type:
dccSectionOverheadBytes(1),
dccLineOverheadBytes(2),
j0Trace(3),
j1Trace(4),
j2Trace(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This defines the transport mechanism for the Test messages. The
scope of this bit mask is restricted to each link encoding
type. The local node will set the bits corresponding to the
various mechanisms it can support for transmitting LMP Test
messages. The receiver chooses the appropriate mechanism in the
BeginVerifyAck message."
REFERENCE
"Link Management Protocol, RFC 4204
Synchronous Optical Network (SONET)/Synchronous Digital
Hierarchy (SDH) Encoding for Link Management Protocol (LMP)
Test Messages, RFC 4207"
::= { lmpLinkVerificationEntry 3 }
lmpLinkVerifyAllLinks OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A value of true(2) for this object indicates that the
verification process checks all unallocated links, otherwise
only the new ports or component links that have been added to
this TE link are verified."
::= { lmpLinkVerificationEntry 4 }
lmpLinkVerifyTransmissionRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the transmission rate of the data link over which
the Test messages will be transmitted and is expressed in
bytes per second."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpLinkVerificationEntry 5 }
lmpLinkVerifyWavelength OBJECT-TYPE
SYNTAX Unsigned32
UNITS "nanometers"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value corresponds to the wavelength at
which the Test messages will be transmitted and is
measured in nanometers (nm). If each data-bearing link
corresponds to a separate wavelength, then this value should
be set to 0."
REFERENCE
"Link Management Protocol, RFC 4204"
::= { lmpLinkVerificationEntry 6 }
lmpLinkVerifyRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. None of the writable objects
in a row can be changed if the status is active(1).
All read-create objects must have valid and consistent
values before the row can be activated."
::= { lmpLinkVerificationEntry 7 }
lmpLinkVerifyStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
lmpLinkVerificationTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row."
DEFVAL { nonVolatile }
::= { lmpLinkVerificationEntry 8 }
-- End of lmpLinkVerificationTable
-- LMP TE Link Performance Table
lmpTeLinkPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF LmpTeLinkPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies LMP TE link performance counters."
::= { lmpObjects 15 }
lmpTeLinkPerfEntry OBJECT-TYPE
SYNTAX LmpTeLinkPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by an LMP-enabled device for
every TE link. lmpTeCounterDiscontinuityTime is used
to indicate potential discontinuity for all counter objects
in this table."
INDEX { ifIndex }
::= { lmpTeLinkPerfTable 1 }
LmpTeLinkPerfEntry ::= SEQUENCE {
lmpTeInOctets Counter32,
lmpTeOutOctets Counter32,
lmpTeBeginVerifyReceived Counter32,
lmpTeBeginVerifySent Counter32,
lmpTeBeginVerifyRetransmit Counter32,
lmpTeBeginVerifyAckReceived Counter32,
lmpTeBeginVerifyAckSent Counter32,
lmpTeBeginVerifyNackReceived Counter32,
lmpTeBeginVerifyNackSent Counter32,
lmpTeEndVerifyReceived Counter32,
lmpTeEndVerifySent Counter32,
lmpTeEndVerifyRetransmit Counter32,
lmpTeEndVerifyAckReceived Counter32,
lmpTeEndVerifyAckSent Counter32,
lmpTeTestStatusSuccessReceived Counter32,
lmpTeTestStatusSuccessSent Counter32,
lmpTeTestStatusSuccessRetransmit Counter32,
lmpTeTestStatusFailureReceived Counter32,
lmpTeTestStatusFailureSent Counter32,
lmpTeTestStatusFailureRetransmit Counter32,
lmpTeTestStatusAckReceived Counter32,
lmpTeTestStatusAckSent Counter32,
lmpTeLinkSummaryReceived Counter32,
lmpTeLinkSummarySent Counter32,
lmpTeLinkSummaryRetransmit Counter32,
lmpTeLinkSummaryAckReceived Counter32,
lmpTeLinkSummaryAckSent Counter32,
lmpTeLinkSummaryNackReceived Counter32,
lmpTeLinkSummaryNackSent Counter32,
lmpTeChannelStatusReceived Counter32,
lmpTeChannelStatusSent Counter32,
lmpTeChannelStatusRetransmit Counter32,
lmpTeChannelStatusAckReceived Counter32,
lmpTeChannelStatusAckSent Counter32,
lmpTeChannelStatusReqReceived Counter32,
lmpTeChannelStatusReqSent Counter32,
lmpTeChannelStatusReqRetransmit Counter32,
lmpTeChannelStatusRspReceived Counter32,
lmpTeChannelStatusRspSent Counter32,
lmpTeCounterDiscontinuityTime TimeStamp
}
lmpTeInOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of LMP message octets received for
this TE link."
::= { lmpTeLinkPerfEntry 1 }
lmpTeOutOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of LMP message octets transmitted out
for this TE link."
::= { lmpTeLinkPerfEntry 2 }
lmpTeBeginVerifyReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that have
been received for this TE link."
::= { lmpTeLinkPerfEntry 3 }
lmpTeBeginVerifySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that have
been sent for this TE link."
::= { lmpTeLinkPerfEntry 4 }
lmpTeBeginVerifyRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerify messages that
have been retransmitted for this TE link."
::= { lmpTeLinkPerfEntry 5 }
lmpTeBeginVerifyAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyAck messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 6 }
lmpTeBeginVerifyAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyAck messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 7 }
lmpTeBeginVerifyNackReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyNack messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 8 }
lmpTeBeginVerifyNackSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of BeginVerifyNack messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 9 }
lmpTeEndVerifyReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that have
been received for this TE link."
::= { lmpTeLinkPerfEntry 10 }
lmpTeEndVerifySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that have
been sent for this TE link."
::= { lmpTeLinkPerfEntry 11 }
lmpTeEndVerifyRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerify messages that
have been retransmitted over this control channel."
::= { lmpTeLinkPerfEntry 12 }
lmpTeEndVerifyAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerifyAck messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 13 }
lmpTeEndVerifyAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of EndVerifyAck messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 14 }
lmpTeTestStatusSuccessReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been received for this TE link."
::= { lmpTeLinkPerfEntry 15 }
lmpTeTestStatusSuccessSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been sent for this TE link."
::= { lmpTeLinkPerfEntry 16 }
lmpTeTestStatusSuccessRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusSuccess messages
that have been retransmitted for this TE link."
::= { lmpTeLinkPerfEntry 17 }
lmpTeTestStatusFailureReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been received for this TE link."
::= { lmpTeLinkPerfEntry 18 }
lmpTeTestStatusFailureSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been sent for this TE link."
::= { lmpTeLinkPerfEntry 19 }
lmpTeTestStatusFailureRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusFailure messages
that have been retransmitted on this TE link."
::= { lmpTeLinkPerfEntry 20 }
lmpTeTestStatusAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusAck messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 21 }
lmpTeTestStatusAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of TestStatusAck messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 22 }
lmpTeLinkSummaryReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 23 }
lmpTeLinkSummarySent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 24 }
lmpTeLinkSummaryRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummary messages that
have been retransmitted over this control channel."
::= { lmpTeLinkPerfEntry 25 }
lmpTeLinkSummaryAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryAck messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 26 }
lmpTeLinkSummaryAckSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryAck messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 27 }
lmpTeLinkSummaryNackReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryNack messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 28 }
lmpTeLinkSummaryNackSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of LinkSummaryNack messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 29 }
lmpTeChannelStatusReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages that
have been received for this TE link."
::= { lmpTeLinkPerfEntry 30 }
lmpTeChannelStatusSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages that
have been sent for this TE link."
::= { lmpTeLinkPerfEntry 31 }
lmpTeChannelStatusRetransmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatus messages that
have been retransmitted for this TE link."
::= { lmpTeLinkPerfEntry 32 }
lmpTeChannelStatusAckReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of ChannelStatusAck messages
that have been received for this TE link."
::= { lmpTeLinkPerfEntry 33 }