Content for TS 37.171 Word version: 18.0.0
1 Scope
2 References
3 Definitions, abbreviations and test tolerances
3.1 Definitions
3.2 Abbreviations
3.3 Test tolerances
...
...
1 Scope p. 7
The present document establishes the minimum performance requirements for RAT-Independent Positioning Enhancements for FDD and TDD mode of UTRA, FDD and TDD mode of E-UTRA, and NR for the User Equipment (UE).
2 References p. 7
The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific.
- For a specific reference, subsequent revisions do not apply.
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document.
[1]
TR 21.905: "Vocabulary for 3GPP Specifications".
[2]
ETSI TR 102 273-1-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 1: Uncertainties in the measurement of mobile radio equipment characteristics; Sub-part 2: Examples and annexes".
[3]
TS 36.355: "Evolved Universal Terrestrial Radio Access (E-UTRA); LTE Positioning Protocol (LPP)".
[4]
TS 36.509: "Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet Core (EPC); Special conformance testing functions for User Equipment (UE)".
[5]
TS 36.942: Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Frequency (RF) system scenarios".
[6]
TS 25.331: "Radio Resource Control (RRC); Protocol specification".
[7]
ATIS-0500027: "Recommendations for Establishing Wide Scale Indoor Location Performance", May 2015.
[8]
TS 34.109: "Terminal logical test interface; Special conformance testing functions ".
[9]
TS 37.571-1: " User Equipment (UE) conformance specification for UE positioning; Part 1: Conformance test specification ".
[10]
TS 36.521-1: "Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) conformance specification; Radio transmission and reception; Part 1: Conformance testing".
[11] Void.
[12]
TS 36.355: "Evolved Universal Terrestrial Radio Access (E-UTRA); LTE Positioning Protocol (LPP)".
[13]
Bluetooth Special Interest Group: "Bluetooth Core Specification version 4.2", December 2014.
[14]
TS 36.331: "Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Resource Control (RRC) protocol specification".
[15]
IEEE Standard 802.11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications.
[16]
TS 38.509: "5GS; Special conformance testing functions for User Equipment (UE)".
3 Definitions, abbreviations and test tolerances p. 8
3.1 Definitions p. 8
For the purposes of the present document, the terms and definitions given in TR 21.905 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905.
3.2 Abbreviations p. 8
For the purposes of the present document, the abbreviations given in TR 21.905 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905.
AWGN
Additive White Gaussian Noise
EPA
Extended Pedestrian A
E-UTRA
Evolved UMTS Terrestrial Radio Access
FDD
Frequency Division Duplex
LMF
Location Management Function
LPP
LTE Positioning Protocol
MBS
Metropolitan Beacon System
NR
New Radio Access
RRC
Radio Resource Control
RSSI
Received Signal Strength Indicator
SS
System Simulator
TDD
Time Division Duplex
UE
User Equipment
UTRA
UMTS Terrestrial Radio Access
WLAN
Wireless Local Area Network
3.3 Test tolerances p. 8
The requirements given in the present document make no allowance for measurement uncertainty. The test specification TS 37.571-1 will define test tolerances. These test tolerances are individually calculated for each test. The test tolerances are then added to the limits in the present document to create test limits. The measurement results are compared against the test limits as defined by the shared risk principle.
Shared Risk is defined in ETSI TR 102 273-1-2 [2], subclause 6.5.
