RFC 3231
Definitions of Managed Objects for Scheduling Management Operations
Network Working Group D. Levi Request for Comments: 3231 Nortel Networks Obsoletes: 2591 J. Schoenwaelder Category: Standards Track TU Braunschweig January 2002 Definitions of Managed Objects for Scheduling Management Operations Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (2002). All Rights Reserved.Abstract
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes a set of managed objects that are used to schedule management operations periodically or at specified dates and times. This document obsoletes RFC 2591.Table of Contents
1 Introduction ................................................. 2 2 The SNMP Management Framework ................................ 2 3 Overview ..................................................... 3 3.1 Periodic Schedules ......................................... 4 3.2 Calendar Schedules ......................................... 4 3.3 One-shot Schedules ......................................... 5 3.4 Time Transitions ........................................... 5 3.5 Actions .................................................... 5 4 Definitions .................................................. 6 5 Usage Examples ............................................... 20 5.1 Starting a script to ping devices every 20 minutes ......... 20 5.2 Starting a script at the next Friday the 13th .............. 21 5.3 Turning an interface off during weekends ................... 22
6 Security Considerations ...................................... 23 7 Intellectual Property ........................................ 25 8 Changes from RFC 2591 ........................................ 25 9 Acknowledgments .............................................. 26 10 References .................................................. 26 11 Editors' Addresses .......................................... 28 12 Full Copyright Statement .................................... 291. Introduction
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes a set of managed objects that are used to schedule management operations periodically or at specified dates and times. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2571 [RFC2571]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC 1215 [RFC1215]. The second version, called SMIv2, is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15, RFC 1157 [RFC1157]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [RFC1901] and RFC 1906 [RFC1906]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [RFC1906], RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [RFC1157]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[RFC1905].
o A set of fundamental applications described in RFC 2573 [RFC2573]
and the view-based access control mechanism described in RFC 2575
[RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
3. Overview
The MIB defined in this memo provides the scheduling of actions
periodically or at specified dates and times. The actions can be
used to realize on-duty / off-duty schedules or to trigger management
functions in a distributed management application.
Schedules can be enabled or disabled by modifying a control object.
This allows for pre-configured schedules which are activated or
deactivated by some other management functions.
The term `scheduler' is used throughout this memo to refer to the
entity which implements the scheduling MIB and which invokes the
actions at the specified points in time.
3.1. Periodic Schedules
Periodic schedules are based on fixed time periods between the initiation of scheduled actions. Periodic schedules are defined by specifying the number of seconds between two initiations. The time needed to complete the action is usually not known by the scheduler and does therefore not influence the next scheduling point. Implementations must guarantee that action invocations will not occur before their next scheduled time. However, implementations may be forced to delay invocations in the face of local constraints (e.g., a heavy load on higher-priority tasks). An accumulation of such delays would result in a drift of the scheduling interval with respect to time, and should be avoided. Scheduled actions collecting statistical data should retrieve time stamps from the data source and not rely on the accuracy of the periodic scheduler in order to obtain accurate statistics.3.2. Calendar Schedules
Calendar schedules trigger scheduled actions at specified days of the week and days of the month. Calendar schedules are therefore aware of the notion of months, days, weekdays, hours and minutes. It is possible to specify multiple values for each calendar item. This provides a mechanism for defining complex schedules. For example, a schedule could be defined which triggers an action every 15 minutes on a given weekday. Months, days and weekdays are specified using the objects schedMonth, schedDay and schedWeekDay of type BITS. Setting multiple bits to one in these objects causes an OR operation. For example, setting the bits monday(1) and friday(5) in schedWeekDay restricts the schedule to Mondays and Fridays. The bit fields for schedMonth, schedDay and schedWeekDay are combined using an AND operation. For example, setting the bits june(5) and july(6) in schedMonth and combining it with the bits monday(1) and friday(5) set in schedWeekDay will result in a schedule which is restricted to every Monday and Friday in the months June and July. Wildcarding of calendar items is achieved by setting all bits to one. It is possible to define calendar schedules that will never trigger an action. For example, one can define a calendar schedule which should trigger an action on February 31st. Schedules like this will simply be ignored by the scheduler.
Finally, calendar schedules are always expressed in local time. A scalar, schedLocalTime, is provided so that a manager can retrieve the notion of local time and the offset to GMT time.3.3. One-shot Schedules
One-shot Schedules are similar to calendar schedules. The difference between a calendar schedule and a one-shot schedule is that a one- shot schedule will automatically disable itself once an action has been invoked.3.4. Time Transitions
A time transition occurs when the Schedule MIB's notion of time (as reported by schedLocalTime) is changed so that time continuity is lost. Time transitions may be caused by daylight savings times or administrative changes of the system's notion of time. There are two possible situations when a time transition occurs. First, time may be set backwards, in which case particular times will appear to occur twice. These are called 'ambiguous times'. Second, time may be set forwards, in which case particular times will not occur. These are called 'nonexistent times'. When an action is configured in the Schedule MIB to occur at an ambiguous time, the action will be invoked at all occurrences of the ambiguous time. For example, if an action is scheduled to occur at 2:10 am, and a time transition occurs at 3:00 am which sets the clock back to 2:00 am, the action will be invoked twice. When an action is configured in the Schedule MIB to occur at a nonexistent time, the action will not be invoked at all. For example, if an action is scheduled to occur at 2:10 am, and a time transition occurs at 2:00 am which sets the clock to 3:00 am, the action will not be invoked.3.5. Actions
Scheduled actions are modeled by SNMP set operations on local MIB variables. Scheduled actions described in this MIB are further restricted to objects of type INTEGER. This restriction does not limit the usefulness of the MIB. Simple schedules such as on-duty / off-duty schedules for resources that have a status MIB object (e.g. ifAdminStatus) are possible.
More complex actions can be realized by triggering a management script which is responsible for performing complex state transitions. A management script can also be used to perform SNMP set operations on remote SNMP engines.4. Definitions
DISMAN-SCHEDULE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32, Counter32, mib-2, zeroDotZero FROM SNMPv2-SMI TEXTUAL-CONVENTION, DateAndTime, RowStatus, StorageType, VariablePointer FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB; schedMIB MODULE-IDENTITY LAST-UPDATED "200201070000Z" ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO "WG EMail: disman@dorothy.bmc.com Subscribe: disman-request@dorothy.bmc.com Chair: Randy Presuhn BMC Software, Inc. Postal: Office 1-3141 2141 North First Street San Jose, California 95131 USA EMail: rpresuhn@bmc.com Phone: +1 408 546-1006 Editor: David B. Levi Nortel Networks Postal: 4401 Great America Parkway Santa Clara, CA 95052-8185 USA EMail: dlevi@nortelnetworks.com Phone: +1 865 686 0432
Editor: Juergen Schoenwaelder
TU Braunschweig
Postal: Bueltenweg 74/75
38106 Braunschweig
Germany
EMail: schoenw@ibr.cs.tu-bs.de
Phone: +49 531 391-3283"
DESCRIPTION
"This MIB module defines a MIB which provides mechanisms to
schedule SNMP set operations periodically or at specific
points in time."
REVISION "200201070000Z"
DESCRIPTION
"Revised version, published as RFC 3231.
This revision introduces a new object type called
schedTriggers. Created new conformance and compliance
statements that take care of the new schedTriggers object.
Several clarifications have been added to remove ambiguities
that were discovered and reported by implementors."
REVISION "199811171800Z"
DESCRIPTION
"Initial version, published as RFC 2591."
::= { mib-2 63 }
--
-- The various groups defined within this MIB definition:
--
schedObjects OBJECT IDENTIFIER ::= { schedMIB 1 }
schedNotifications OBJECT IDENTIFIER ::= { schedMIB 2 }
schedConformance OBJECT IDENTIFIER ::= { schedMIB 3 }
--
-- Textual Conventions:
--
SnmpPduErrorStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC enumerates the SNMPv1 and SNMPv2 PDU error status
codes as defined in RFC 1157 and RFC 1905. It also adds a
pseudo error status code `noResponse' which indicates a
timeout condition."
SYNTAX INTEGER {
noResponse(-1),
noError(0),
tooBig(1),
noSuchName(2),
badValue(3),
readOnly(4),
genErr(5),
noAccess(6),
wrongType(7),
wrongLength(8),
wrongEncoding(9),
wrongValue(10),
noCreation(11),
inconsistentValue(12),
resourceUnavailable(13),
commitFailed(14),
undoFailed(15),
authorizationError(16),
notWritable(17),
inconsistentName(18)
}
--
-- Some scalars which provide information about the local time zone.
--
schedLocalTime OBJECT-TYPE
SYNTAX DateAndTime (SIZE (11))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local time used by the scheduler. Schedules which
refer to calendar time will use the local time indicated
by this object. An implementation MUST return all 11 bytes
of the DateAndTime textual-convention so that a manager
may retrieve the offset from GMT time."
::= { schedObjects 1 }
--
-- The schedule table which controls the scheduler.
--
schedTable OBJECT-TYPE
SYNTAX SEQUENCE OF SchedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines scheduled actions triggered by
SNMP set operations."
::= { schedObjects 2 }
schedEntry OBJECT-TYPE
SYNTAX SchedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry describing a particular scheduled action.
Unless noted otherwise, writable objects of this row
can be modified independent of the current value of
schedRowStatus, schedAdminStatus and schedOperStatus.
In particular, it is legal to modify schedInterval
and the objects in the schedCalendarGroup when
schedRowStatus is active and schedAdminStatus and
schedOperStatus are both enabled."
INDEX { schedOwner, schedName }
::= { schedTable 1 }
SchedEntry ::= SEQUENCE {
schedOwner SnmpAdminString,
schedName SnmpAdminString,
schedDescr SnmpAdminString,
schedInterval Unsigned32,
schedWeekDay BITS,
schedMonth BITS,
schedDay BITS,
schedHour BITS,
schedMinute BITS,
schedContextName SnmpAdminString,
schedVariable VariablePointer,
schedValue Integer32,
schedType INTEGER,
schedAdminStatus INTEGER,
schedOperStatus INTEGER,
schedFailures Counter32,
schedLastFailure SnmpPduErrorStatus,
schedLastFailed DateAndTime,
schedStorageType StorageType,
schedRowStatus RowStatus,
schedTriggers Counter32
}
schedOwner OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The owner of this scheduling entry. The exact semantics of
this string are subject to the security policy defined by
the security administrator."
::= { schedEntry 1 }
schedName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locally-unique, administratively assigned name for this
scheduling entry. This object allows a schedOwner to have
multiple entries in the schedTable."
::= { schedEntry 2 }
schedDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The human readable description of the purpose of this
scheduling entry."
DEFVAL { "" }
::= { schedEntry 3 }
schedInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between two action invocations of
a periodic scheduler. Implementations must guarantee
that action invocations will not occur before at least
schedInterval seconds have passed.
The scheduler must ignore all periodic schedules that
have a schedInterval value of 0. A periodic schedule
with a scheduling interval of 0 seconds will therefore
never invoke an action.
Implementations may be forced to delay invocations in the
face of local constraints. A scheduled management function
should therefore not rely on the accuracy provided by the
scheduler implementation.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { 0 }
::= { schedEntry 4 }
schedWeekDay OBJECT-TYPE
SYNTAX BITS {
sunday(0),
monday(1),
tuesday(2),
wednesday(3),
thursday(4),
friday(5),
saturday(6)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of weekdays on which the scheduled action should
take place. Setting multiple bits will include several
weekdays in the set of possible weekdays for this schedule.
Setting all bits will cause the scheduler to ignore the
weekday.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { {} }
::= { schedEntry 5 }
schedMonth OBJECT-TYPE
SYNTAX BITS {
january(0),
february(1),
march(2),
april(3),
may(4),
june(5),
july(6),
august(7),
september(8),
october(9),
november(10),
december(11)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of months during which the scheduled action should
take place. Setting multiple bits will include several
months in the set of possible months for this schedule.
Setting all bits will cause the scheduler to ignore the
month.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { {} }
::= { schedEntry 6 }
schedDay OBJECT-TYPE
SYNTAX BITS {
d1(0), d2(1), d3(2), d4(3), d5(4),
d6(5), d7(6), d8(7), d9(8), d10(9),
d11(10), d12(11), d13(12), d14(13), d15(14),
d16(15), d17(16), d18(17), d19(18), d20(19),
d21(20), d22(21), d23(22), d24(23), d25(24),
d26(25), d27(26), d28(27), d29(28), d30(29),
d31(30),
r1(31), r2(32), r3(33), r4(34), r5(35),
r6(36), r7(37), r8(38), r9(39), r10(40),
r11(41), r12(42), r13(43), r14(44), r15(45),
r16(46), r17(47), r18(48), r19(49), r20(50),
r21(51), r22(52), r23(53), r24(54), r25(55),
r26(56), r27(57), r28(58), r29(59), r30(60),
r31(61)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of days in a month on which a scheduled action
should take place. There are two sets of bits one can
use to define the day within a month:
Enumerations starting with the letter 'd' indicate a
day in a month relative to the first day of a month.
The first day of the month can therefore be specified
by setting the bit d1(0) and d31(30) means the last
day of a month with 31 days.
Enumerations starting with the letter 'r' indicate a
day in a month in reverse order, relative to the last
day of a month. The last day in the month can therefore
be specified by setting the bit r1(31) and r31(61) means
the first day of a month with 31 days.
Setting multiple bits will include several days in the set
of possible days for this schedule. Setting all bits will
cause the scheduler to ignore the day within a month.
Setting all bits starting with the letter 'd' or the
letter 'r' will also cause the scheduler to ignore the
day within a month.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { {} }
::= { schedEntry 7 }
schedHour OBJECT-TYPE
SYNTAX BITS {
h0(0), h1(1), h2(2), h3(3), h4(4),
h5(5), h6(6), h7(7), h8(8), h9(9),
h10(10), h11(11), h12(12), h13(13), h14(14),
h15(15), h16(16), h17(17), h18(18), h19(19),
h20(20), h21(21), h22(22), h23(23)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of hours within a day during which the scheduled
action should take place.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { {} }
::= { schedEntry 8 }
schedMinute OBJECT-TYPE
SYNTAX BITS {
m0(0), m1(1), m2(2), m3(3), m4(4),
m5(5), m6(6), m7(7), m8(8), m9(9),
m10(10), m11(11), m12(12), m13(13), m14(14),
m15(15), m16(16), m17(17), m18(18), m19(19),
m20(20), m21(21), m22(22), m23(23), m24(24),
m25(25), m26(26), m27(27), m28(28), m29(29),
m30(30), m31(31), m32(32), m33(33), m34(34),
m35(35), m36(36), m37(37), m38(38), m39(39),
m40(40), m41(41), m42(42), m43(43), m44(44),
m45(45), m46(46), m47(47), m48(48), m49(49),
m50(50), m51(51), m52(52), m53(53), m54(54),
m55(55), m56(56), m57(57), m58(58), m59(59)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The set of minutes within an hour when the scheduled action
should take place.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { {} }
::= { schedEntry 9 }
schedContextName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The context which contains the local MIB variable pointed
to by schedVariable."
DEFVAL { "" }
::= { schedEntry 10 }
schedVariable OBJECT-TYPE
SYNTAX VariablePointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object identifier pointing to a local MIB variable
which resolves to an ASN.1 primitive type of INTEGER."
DEFVAL { zeroDotZero }
::= { schedEntry 11 }
schedValue OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value which is written to the MIB object pointed to by
schedVariable when the scheduler invokes an action. The
implementation shall enforce the use of access control
rules when performing the set operation on schedVariable.
This is accomplished by calling the isAccessAllowed abstract
service interface as defined in RFC 2571.
Note that an implementation may choose to issue an SNMP Set
message to the SNMP engine and leave the access control
decision to the normal message processing procedure."
DEFVAL { 0 }
::= { schedEntry 12 }
schedType OBJECT-TYPE
SYNTAX INTEGER {
periodic(1),
calendar(2),
oneshot(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of this schedule. The value periodic(1) indicates
that this entry specifies a periodic schedule. A periodic
schedule is defined by the value of schedInterval. The
values of schedWeekDay, schedMonth, schedDay, schedHour
and schedMinute are ignored.
The value calendar(2) indicates that this entry describes a
calendar schedule. A calendar schedule is defined by the
values of schedWeekDay, schedMonth, schedDay, schedHour and
schedMinute. The value of schedInterval is ignored. A
calendar schedule will trigger on all local times that
satisfy the bits set in schedWeekDay, schedMonth, schedDay,
schedHour and schedMinute.
The value oneshot(3) indicates that this entry describes a
one-shot schedule. A one-shot schedule is similar to a
calendar schedule with the additional feature that it
disables itself by changing in the `finished'
schedOperStatus once the schedule triggers an action.
Note that implementations which maintain a list of pending
activations must re-calculate them when this object is
changed."
DEFVAL { periodic }
::= { schedEntry 13 }
schedAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The desired state of the schedule."
DEFVAL { disabled }
::= { schedEntry 14 }
schedOperStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2),
finished(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current operational state of this schedule. The state
enabled(1) indicates this entry is active and that the
scheduler will invoke actions at appropriate times. The
disabled(2) state indicates that this entry is currently
inactive and ignored by the scheduler. The finished(3)
state indicates that the schedule has ended. Schedules
in the finished(3) state are ignored by the scheduler.
A one-shot schedule enters the finished(3) state when it
deactivates itself.
Note that the operational state must not be enabled(1)
when the schedRowStatus is not active."
::= { schedEntry 15 }
schedFailures OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable counts the number of failures while invoking
the scheduled action. This counter at most increments once
for a triggered action."
::= { schedEntry 16 }
schedLastFailure OBJECT-TYPE
SYNTAX SnmpPduErrorStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The most recent error that occurred during the invocation of
a scheduled action. The value noError(0) is returned
if no errors have occurred yet."
DEFVAL { noError }
::= { schedEntry 17 }
schedLastFailed OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The date and time when the most recent failure occurred.
The value '0000000000000000'H is returned if no failure
occurred since the last re-initialization of the scheduler."
DEFVAL { '0000000000000000'H }
::= { schedEntry 18 }
schedStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this scheduled action is kept
in volatile storage and lost upon reboot or if this row is
backed up by non-volatile or permanent storage.
Conceptual rows having the value `permanent' must allow
write access to the columnar objects schedDescr,
schedInterval, schedContextName, schedVariable, schedValue,
and schedAdminStatus. If an implementation supports the
schedCalendarGroup, write access must be also allowed to
the columnar objects schedWeekDay, schedMonth, schedDay,
schedHour, schedMinute."
DEFVAL { volatile }
::= { schedEntry 19 }
schedRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this scheduled action. A control that allows
entries to be added and removed from this table.
Note that the operational state must change to enabled
when the administrative state is enabled and the row
status changes to active(1).
Attempts to destroy(6) a row or to set a row
notInService(2) while the operational state is enabled
result in inconsistentValue errors.
The value of this object has no effect on whether other
objects in this conceptual row can be modified."
::= { schedEntry 20 }
schedTriggers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable counts the number of attempts (either
successful or failed) to invoke the scheduled action."
::= { schedEntry 21 }
--
-- Notifications that are emitted to indicate failures. The
-- definition of schedTraps makes notification registrations
-- reversible (see STD 58, RFC 2578).
--
schedTraps OBJECT IDENTIFIER ::= { schedNotifications 0 }
schedActionFailure NOTIFICATION-TYPE
OBJECTS { schedLastFailure, schedLastFailed }
STATUS current
DESCRIPTION
"This notification is generated whenever the invocation of a
scheduled action fails."
::= { schedTraps 1 }
-- conformance information
schedCompliances OBJECT IDENTIFIER ::= { schedConformance 1 }
schedGroups OBJECT IDENTIFIER ::= { schedConformance 2 }
-- compliance statements
schedCompliance2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which implement
the scheduling MIB."
MODULE -- this module
MANDATORY-GROUPS {
schedGroup2, schedNotificationsGroup
}
GROUP schedCalendarGroup
DESCRIPTION
"The schedCalendarGroup is mandatory only for those
implementations that support calendar based schedules."
OBJECT schedType
DESCRIPTION
"The values calendar(2) or oneshot(3) are not valid for
implementations that do not implement the
schedCalendarGroup. Such an implementation must return
inconsistentValue error responses for attempts to set
schedAdminStatus to calendar(2) or oneshot(3)."
::= { schedCompliances 2 }
schedGroup2 OBJECT-GROUP
OBJECTS {
schedDescr, schedInterval, schedContextName,
schedVariable, schedValue, schedType,
schedAdminStatus, schedOperStatus, schedFailures,
schedLastFailure, schedLastFailed, schedStorageType,
schedRowStatus, schedTriggers
}
STATUS current
DESCRIPTION
"A collection of objects providing scheduling capabilities."
::= { schedGroups 4 }
schedCalendarGroup OBJECT-GROUP
OBJECTS {
schedLocalTime, schedWeekDay, schedMonth,
schedDay, schedHour, schedMinute
}
STATUS current
DESCRIPTION
"A collection of objects providing calendar based schedules."
::= { schedGroups 2 }
schedNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
schedActionFailure
}
STATUS current
DESCRIPTION
"The notifications emitted by the scheduler."
::= { schedGroups 3 }
--
-- Deprecated compliance and conformance group definitions
-- from RFC 2591.
--
schedCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for SNMP entities which implement
the scheduling MIB."
MODULE -- this module
MANDATORY-GROUPS {
schedGroup, schedNotificationsGroup
}
GROUP schedCalendarGroup
DESCRIPTION
"The schedCalendarGroup is mandatory only for those
implementations that support calendar based schedules."
OBJECT schedType
DESCRIPTION
"The values calendar(2) or oneshot(3) are not valid for
implementations that do not implement the
schedCalendarGroup. Such an implementation must return
inconsistentValue error responses for attempts to set
schedAdminStatus to calendar(2) or oneshot(3)."
::= { schedCompliances 1 }
schedGroup OBJECT-GROUP
OBJECTS {
schedDescr, schedInterval, schedContextName,
schedVariable, schedValue, schedType,
schedAdminStatus, schedOperStatus, schedFailures,
schedLastFailure, schedLastFailed, schedStorageType,
schedRowStatus
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing scheduling capabilities."
::= { schedGroups 1 }
END
5. Usage Examples
This section presents some examples how the scheduling MIB can be
used to schedule scripts with the Script MIB [RFC3165] or to realize
on-duty/off-duty schedules by modifying status objects of other MIB
modules.
5.1. Starting a script to ping devices every 20 minutes
It is assumed that the schedule entry is owned by schedOwner = "joe"
and its name is schedName = "ping". The instance identifier for the
scheduling entry is therefore 3.106.111.101.4.112.105.110.103.
It is further assumed that the smLaunchTable entry is owned by
smLaunchOwner = "joe" and its name is smLaunchName = "ping-devs".
The complete object identifier for the smLaunchStart object is
therefore
smLaunchStart.3.106.111.101.9.112.105.110.103.45.100.101.118.115.
The script lives in the context identified by the string "engine1".
The configuration of the scheduler entry which launches the script
every 20 minutes would look as follows:
schedInterval.3.106.111.101.4.112.105.110.103 = 1200
schedValue.3.106.111.101.4.112.105.110.103 = 0
schedContextName.3.106.111.101.4.112.105.110.103 = "engine1"
schedVariable.3.106.111.101.4.112.105.110.103 =
smLaunchStart.3.106.111.101.9.112.105.110.103.45.100.101.118.115
schedType.3.106.111.101.4.112.105.110.103 = periodic(1)
schedAdminStatus.3.106.111.101.4.112.105.110.103 = enabled(1)
schedStorageType.3.106.111.101.4.112.105.110.103 = nonVolatile(3)
schedRowStatus.3.106.111.101.4.112.105.110.103 = active(1)
All the remaining columns in the schedTable represent status
information and are not shown here.
5.2. Starting a script at the next Friday the 13th
It is assumed that the schedule entry is owned by schedOwner = "joe"
and its name is schedName = "13th". The instance identifier for the
scheduling entry is therefore 3.106.111.101.4.49.51.116.104.
It is further assumed that the smLaunchTable entry is owned by
smLaunchOwner = "joe" and its name is smLaunchName = "ghost". The
complete object identifier for the smLaunchStart object is therefore
smLaunchStart.3.106.111.101.5.103.104.111.115.116. The script lives
in the context identified by the string "engine1".
The configuration of the scheduler entry which launches the script on
the next Friday 13th at midnight would look as follows:
schedWeekDay.3.106.111.101.4.49.51.116.104 = { friday }
schedMonth.3.106.111.101.4.49.51.116.104 = {
january, february, march, april, may, june,
july, august, september, october, november, december
}
schedDay.3.106.111.101.4.49.51.116.104 = { d13 }
schedHour.3.106.111.101.4.49.51.116.104 = { h0 }
schedMinute.3.106.111.101.4.49.51.116.104 = { m0 }
schedValue.3.106.111.101.4.49.51.116.104 = 0
schedContextName.3.106.111.101.4.49.51.116.104 = "engine1"
schedVariable.3.106.111.101.4.49.51.116.104 =
smLaunchStart.3.106.111.101.5.103.104.111.115.116
schedType.3.106.111.101.4.49.51.116.104 = oneshot(3)
schedAdminStatus.3.106.111.101.4.49.51.116.104 = enabled(2)
schedStorageType.3.106.111.101.4.49.51.116.104 = nonVolatile(3)
schedRowStatus.3.106.111.101.4.49.51.116.104 = active(1)
All the remaining columns in the schedTable represent status
information and are not shown here.
5.3. Turning an interface off during weekends
This example assumes that a network interface should be taken down
during weekends. The interface table (ifTable) of the IF-MIB
[RFC2863] is assumed to exist in the context identified by an empty
string and the index of the interface is ifIndex = 6.
The scheduling entry which brings the interface down on every Friday
evening at 20:30 (8:30 pm) is owned by schedOwner = "bob" and its
name is schedName = "if-off". The instance identifier for the
scheduling entry is therefore 3.98.111.98.6.105.102.45.111.102.102.
schedWeekDay.3.98.111.98.6.105.102.45.111.102.102 = { friday }
schedMonth.3.98.111.98.6.105.102.45.111.102.102 = {
january, february, march, april, may, june,
july, august, september, october, november, december
}
schedDay.3.98.111.98.6.105.102.45.111.102.102 = {
d1, d2, d3, d4, d5, d6, d7, d8, d9, d10,
d11, d12, d13, d14, d15, d16, d17, d18, d19, d20,
d21, d22, d23, d24, d25, d26, d27, d28, d29, d30, d31
}
schedHour.3.98.111.98.6.105.102.45.111.102.102 = { h20 }
schedMinute.3.98.111.98.6.105.102.45.111.102.102 = { m30 }
schedValue.3.98.111.98.6.105.102.45.111.102.102 = down(2)
schedContextName.3.98.111.98.6.105.102.45.111.102.102 = ""
schedVariable.3.98.111.98.6.105.102.45.111.102.102 =
ifAdminStatus.6
schedType.3.98.111.98.6.105.102.45.111.102.102 = calendar(2)
schedAdminStatus.3.98.111.98.6.105.102.45.111.102.102 = enabled(1)
schedStorageType.3.98.111.98.6.105.102.45.111.102.102 =
nonVolatile(3)
schedRowStatus.3.98.111.98.6.105.102.45.111.102.102 = active(1)
The scheduling entry which brings the interface up on every Monday
morning at 5:30 is owned by schedOwner = "bob" and its name is
schedName = "if-on". The instance identifier for the scheduling
entry is therefore 3.98.111.98.5.105.102.45.111.110.
The entry in the schedTable which brings the interface up again on
every Monday morning at 5:30 looks as follows:
schedWeekDay.3.98.111.98.5.105.102.45.111.110 = { monday }
schedMonth.3.98.111.98.5.105.102.45.111.110 = {
january, february, march, april, may, june,
july, august, september, october, november, december
}
schedDay.3.98.111.98.5.105.102.45.111.110 = {
d1, d2, d3, d4, d5, d6, d7, d8, d9, d10,
d11, d12, d13, d14, d15, d16, d17, d18, d19, d20,
d21, d22, d23, d24, d25, d26, d27, d28, d29, d30, d31
}
schedHour.3.98.111.98.5.105.102.45.111.110 = { h5 }
schedMinute.3.98.111.98.5.105.102.45.111.110 = { m30 }
schedValue.3.98.111.98.5.105.102.45.111.110 = up(1)
schedContextName.3.98.111.98.5.105.102.45.111.110 = ""
schedVariable.3.98.111.98.5.105.102.45.111.110 = ifAdminStatus.6
schedType.3.98.111.98.5.105.102.45.111.110 = calendar(2)
schedAdminStatus.3.98.111.98.5.105.102.45.111.110 = enabled(1)
schedStorageType.3.98.111.98.5.105.102.45.111.110 = nonVolatile(3)
schedRowStatus.3.98.111.98.5.105.102.45.111.110 = active(1)
A similar configuration could be used to control other schedules.
For example, one could change the "if-on" and "if-off" schedules to
enable and disable the periodic scheduler defined in the first
example.
6. Security Considerations
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. Scheduled SNMP set operations must use the security credentials that were present when the corresponding row in the scheduling entry was created. An implementation must therefore record and maintain the credentials for every scheduling entry. An implementation must ensure that access control rules are applied when doing the set operation. This is accomplished by calling the isAccessAllowed abstract service interface defined in RFC 2571 [RFC2571]: statusInformation = -- success or errorIndication isAccessAllowed( IN securityModel -- Security Model in use IN securityName -- principal who wants to access IN securityLevel -- Level of Security IN viewType -- read, write, or notify view IN contextName -- context containing variableName IN variableName -- OID for the managed object ) The securityModel, securityName and securityLevel parameters are set to the values that were recorded when the scheduling entry was created. The viewType parameter must select the write view and the contextName and variableName parameters are taken from the schedContextName and schedVariableName values of the scheduling entry. This MIB limits scheduled actions to objects in the local MIB. This avoids security problems with the delegation of access rights. However, it might be possible for a user of this MIB to own some schedules that might trigger far in the future. This can cause security risks if the security administrator did not properly update the access control lists when a user is withdrawn from an SNMP engine. Therefore, entries in the schedTable SHOULD be cleaned up whenever a user is removed from an SNMP engine. To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (VACM) defined in RFC 2575 [RFC2575] for tables in which multiple users may need to independently create or modify entries, the initial index is used as an "owner index". Such an initial index has a syntax of
SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. All entries in related tables belonging to a particular user will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the "column" subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask "wildcarding" the column subidentifier. More elaborate configurations are possible.7. Intellectual Property
The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP 11, RFC 2028. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.8. Changes from RFC 2591
The following list documents major changes from the previous version of this document, published as RFC 2591: - Updated the SNMP Management Framework boilerplate and the references. - Added revision clauses to the module identity macro. - Clarified the behavior during time transitions.
- Clarified that schedInterval and schedCalendarGroup objects can be
modified regardless of the current value of schedRowStatus,
schedAdminStatus and schedOperStatus.
- Added some additional boilerplate text to the security
considerations section.
- Clarified that implementations must re-calculate any pending
action invocations when scheduling parameters are modified.
- Clarified that schedOperStatus must not be enabled while the
schedRowStatus is not active.
- Clarified that schedRowStatus can not be changed as long as the
schedOperStatus is enabled.
- Clarified that implementations can delegate the isAccessAllowed
check by sending themself an SNMP Set message.
- Added the schedTriggers object which counts the total number of
triggers.
- Added DEFVALs for schedContextName, schedVariable, and schedValue
and updated the schedRowStatus description.
- Deprecated schedCompliance, schedGroup and created
schedCompliance2 and schedGroup2 that take care of the new
schedTriggers object.
9. Acknowledgments
This document was produced by the IETF Distributed Management
(DISMAN) working group.
10. References
[RFC2571] Harrington, D., Presuhn, R. and B. Wijnen, "An
Architecture for Describing SNMP Management Frameworks",
RFC 2571, April 1999.
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991.
[RFC1215] Rose, M., "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990. [RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. [RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996. [RFC2572] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999. [RFC2574] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [RFC2573] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC 2573, April 1999. [RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2570] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999. [RFC2028] Hovey, R. and S. Bradner, "The Organizations Involved in the IETF Standards Process", BCP 11, RFC 2028, October 1996. [RFC3165] Levi, D. and J. Schoenwaelder, "Definitions of Managed Objects for the Delegation of Management Scripts", RFC 3165, August 2001. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.11. Editors' Addresses
David B. Levi Nortel Networks 4401 Great America Parkway Santa Clara, CA 95052-8185 USA Phone: +1 865 686 0432 EMail: dlevi@nortelnetworks.com Juergen Schoenwaelder TU Braunschweig Bueltenweg 74/75 38106 Braunschweig Germany Phone: +49 531 391-3283 EMail: schoenw@ibr.cs.tu-bs.de
12. Full Copyright Statement
Copyright (C) The Internet Society (2002). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.