Tech-invite 3GPPspace IETFspace

21 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 4‑5x

Content for TS 45.005 Word version: 18.0.0

1… 2… A… M…

A Spectrum characteristics (spectrum due to the modulation) p. 188

B (Normative) Transmitted power level versus time p. 196

C (Normative) Propagation conditions p. 202

C.1 Simple wideband propagation model p. 202

C.2 Doppler spectrum types p. 202

C.3 Propagation models p. 202

C.3.1 Typical case for rural area (RAx): (6 tap setting) p. 203

C.3.2 Typical case for hilly terrain (HTx): (12 tap setting) p. 203

C.3.3 Typical case for urban area (TUx): (12 tap setting) p. 204

C.3.4 Profile for equalization test (EQx): (6 tap setting) p. 204

C.3.5 Typical case for very small cells (TIx): (2 tap setting) p. 204

D (Normative) Environmental conditions p. 205

D.1 General p. 205

D.2 Environmental requirements for the MSs p. 205

D.2.1 Temperature (GSM 400, GSM 900, ER-GSM 900 and DCS 1 800) p. 205

D.2.1.1 Environmental Conditions (PCS 1 900, GSM 850 and GSM 700) p. 205

D.2.2 Voltage p. 205

D.2.3 Vibration (GSM 400, GSM 900, ER-GSM 900 and DCS 1 800) p. 206

D.2.3.1 Vibration (PCS 1 900, GSM 850 and GSM 700) p. 206

D.3 Environmental requirements for the BSS equipment p. 206

D.3.1 Environmental requirements for the BSS equipment p. 207

E (Normative) Repeater characteristics p. 208

E.1 Introduction p. 208

E.2 Spurious emissions p. 208

E.3 Intermodulation products p. 209

E.4 Out of band gain p. 209

E.5 Frequency error and modulation accuracy p. 209

E.5.1 Frequency error p. 209

E.5.2 Modulation accuracy at GMSK modulation p. 209

E.5.3 Modulation accuracy at 8-PSK, 16-QAM, 32-QAM, QPSK and AQPSK modulation p. 209

F (Normative) Antenna Feeder Loss Compensator Characteristics (GSM 400, GSM 900 and DCS 1800) p. 211

F.1 Introduction p. 211

F.2 Transmitting path p. 211

F.2.1 Maximum output power p. 211

F.2.2 Gain p. 212

F.2.3 Burst transmission characteristics p. 212

F.2.4 Phase error p. 212

F.2.5 Frequency error p. 213

F.2.6 Group delay p. 213

F.2.7 Spurious emissions p. 213

F.2.8 VSWR p. 214

F.2.9 Stability p. 214

F.3 Receiving path p. 214

F.3.1 Gain p. 214

F.3.2 Noise figure p. 214

F.3.3 Group delay p. 214

F.3.4 Intermodulation performance p. 214

F.3.5 VSWR p. 214

F.3.6 Stability p. 214

F.4 Guidelines (informative) p. 214

G (Normative) Calculation of Error Vector Magnitude p. 216

H (Normative) Requirements on Location Measurement Unit p. 218

H.1 TOA LMU Requirements p. 218

H.1.1 Void

H.1.2 LMU characteristics p. 218

H.1.2.1 Blocking characteristics p. 218

H.1.2.2 AM suppression characteristics p. 218

H.1.2.3 Intermodulation characteristics p. 219

H.1.2.4 Spurious emissions p. 219

H.1.3 Time-of-Arrival Measurement Performance p. 219

H.1.3.1 Sensitivity Performance p. 219

H.1.3.2 Interference Performance p. 220

H.1.3.3 Multipath Performance p. 221

H.1.4 Radio Interface Timing Measurement Performance p. 221

H.2 E-OTD LMU Requirements p. 221

H.2.1 LMU Characteristics p. 221

H.2.1.1 Blocking characteristics p. 222

H.2.1.2 AM suppression characteristics p. 222

H.2.1.3 Intermodulation characteristics p. 222

H.2.2 Sensitivity and Interference Performance p. 222

H.2.2.1 Sensitivity Performance p. 222

H.2.2.2 Interference Performance p. 223

H.2.2.3 Multipath Performance p. 223

I (Normative) E-OTD Mobile Station Requirements p. 225

I.1 Introduction p. 225

I.2 Sensitivity and Interference Performance p. 225

I.2.1 Sensitivity Performance p. 225

I.2.2 Interference Performance p. 226

I.2.3 Multipath Performance p. 226

J Guidance on the Usage of Dynamic ARFCN Mapping p. 226

J.1 Introduction p. 226

J.2 Dynamic allocation of GSM 400, GSM 800, GSM 900, ER-GSM 900, DCS 1800 and PCS 1900 ARFCNs p. 227

J.3 Controlling changes in dynamic mapping p. 227

K (Normative) Reference TFCs for FLO |R6| p. 228

L (Normative) Reference Test Scenarios for DARP |R6| p. 230