Content for TS 37.145-2 Word version: 18.6.0
8 Radiated performance requirements
A Test system characterization
B Calibration
C Test tolerances and derivation of test requirements
D Test system set-up
E Estimation of Measurement Uncertainty
F TRP measurement grids
G Environmental requirements for the BS equipment
H Measuring noise close to noise-floor
$ Change history
8 Radiated performance requirements p. 347
8.1 General p. 347
8.2 Radiated performance requirements for MSR p. 348
8.3 Radiated performance requirements for UTRA FDD p. 348
8.3.1 General p. 348
8.3.2 Definitions and applicability p. 349
8.3.3 Minimum requirements p. 350
8.3.4 Test purposes p. 350
8.3.5 Method of test p. 350
8.3.5.1 Initial conditions p. 350
8.3.5.2 Procedure p. 350
8.3.6 Test requirements p. 351
8.4 Radiated performance requirements for E-UTRA p. 352
8.4.1 General p. 352
8.4.2 Definitions and applicability p. 353
8.4.3 Minimum requirements p. 353
8.4.4 Test purposes p. 353
8.4.5 Method of test p. 354
8.4.5.1 Initial conditions p. 354
8.4.5.2 Procedure p. 354
8.4.6 Test requirements p. 355
8.5 Radiated performance requirements for NR p. 355
8.5.1 General p. 355
8.5.2 Definitions and applicability p. 356
8.5.3 Minimum requirements p. 356
8.5.4 Test purposes p. 357
8.5.5 Method of test p. 357
8.5.5.1 Initial conditions p. 357
8.5.5.2 Procedure p. 357
8.5.6 Test requirements p. 358
A (Normative) Test system characterization p. 359
B (Normative) Calibration p. 360
C Test tolerances and derivation of test requirements p. 361
C.1 General p. 361
C.2 Measurement of transmitter (OTA) p. 362
C.3 Measurement of receiver (OTA) p. 364
D Test system set-up p. 365
D.1 Transmitter p. 365
D.1.1 Radiated Transmit Power, OTA E-UTRA DL RS power, output power dynamics and Transmitter signal quality p. 365
D.1.2 OTA Base Station output power, ACLR, OTA spectrum emissions mask, OTA operating band unwanted emissions p. 366
D.1.3 OTA spurious emissions p. 366
D.1.4 OTA Co-location emissions, TX OFF power p. 367
D.1.5 OTA Transmitter Intermodulation p. 367
D.2 Receiver p. 368
D.2.1 OTA sensitivity and OTA Reference sensitivity p. 368
D.2.2 OTA Dynamic range p. 368
D.2.3 OTA Adjacent channel selectivity, general blocking, and narrowband blocking p. 369
D.2.4 OTA Blocking p. 370
D.2.5 OTA Receiver spurious emissions p. 371
D.2.6 OTA Receiver intermodulation p. 371
D.2.7 OTA In-channel selectivity p. 372
D.3 Performance requirements p. 373
E (Normative) Estimation of Measurement Uncertainty p. 374
E.1 General p. 374
E.2 Measurement methodology descriptions p. 374
E.3 Measurement uncertainty budget format p. 374
E.4 Measurement uncertainty budgets p. 374
E.5 Measurement error contribution descriptions p. 374
F (Normative) TRP measurement grids p. 375
F.1 General p. 375
F.2 Spherical equal angle grid p. 375
F.2.1 General p. 375
F.2.2 Reference angular step criteria p. 375
F.3 Spherical equal area grid p. 377
F.4 Spherical Fibonacci grid p. 378
F.5 Orthogonal cut grid p. 378
F.5.1 General p. 378
F.5.2 Operating band unwanted emissions p. 379
F.5.3 Spurious unwanted emissions p. 379
F.6 Wave vector space grid p. 380
F.7 Orthogonal 2 cuts with pattern multiplication p. 380
F.8 Void
F.9 Full sphere with sparse sampling p. 380
F.10 Beam-based directions p. 381
F.11 Peak method p. 381
F.12 Equal sector with peak average p. 381
F.13 Pre-scan p. 382
G (Normative) Environmental requirements for the BS equipment p. 383
G.1 General p. 383
G.2 Normal test environment p. 383
G.3 Extreme test environment p. 383
G.3.1 General p. 383
G.3.2 Extreme temperature p. 384
G.4 Vibration p. 384
G.5 Power supply p. 384
G.6 Measurement of test environments p. 384
G.7 OTA extreme test methods p. 385
G.7.1 Direct far field method p. 385
G.7.2 Relative method p. 385
H Measuring noise close to noise-floor p. 387
$ Change history p. 388
