Content for TS 36.112 Word version: 18.0.0
1 Scope
2 References
3 Definitions, symbols and abbreviations
3.1 Definitions
3.2 Symbols
3.3 Abbreviations
...
...
1 Scope p. 8
The present document establishes the conformance requirements for E-UTRAN Location Measurement Units (LMU) operating in the FDD or TDD mode.
2 References p. 8
The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific.
- For a specific reference, subsequent revisions do not apply.
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document.
[1]
TR 21.905: "Vocabulary for 3GPP Specifications".
[2]
TS 36.111: "Location Measurement Unit (LMU) performance specification".
[3]
TS 36.211: "Physical channels and modulation".
[4]
IEC 60721-3-3 (2002): "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weather protected locations".
[5]
IEC 60721-3-4 (1995): "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 4: Stationary use at non-weather protected locations".
[6]
IEC 60068-2-1 (2007): "Environmental testing - Part 2: Tests. Tests A: Cold".
[7]
IEC 60068-2-2 (2007): "Environmental testing - Part 2: Tests. Tests B: Dry heat".
[8]
IEC 60068-2-6 (2007): "Environmental testing - Part 2: Tests - Test Fc: Vibration (sinusoidal)".
3 Definitions, symbols and abbreviations p. 8
3.1 Definitions p. 8
For the purposes of the present document, the terms and definitions given in TR 21.905 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905.
3.2 Symbols p. 8
For the purposes of the present document, the following symbols apply:
BWChannel
Channel bandwidth
BWChannel_CA
Aggregated Channel bandwidth
Ês
Received energy per RE (power normalized to the subcarrier spacing) during the useful part of the symbol, i.e. excluding the cyclic prefix, at the LMU antenna connector
Fedge_high
Upper edge of the Aggregated Channel Bandwidth
Fedge_low
Lower edge of the Aggregated Channel Bandwidth
Io
The total received power density, including signal and interference, as measured at the UE antenna connector
Iot
The received power spectral density of the total noise and interference for a certain RE (power integrated over the RE and normalized to the subcarrier spacing) as measured at the LMU antenna connector
Ts
The basic unit of time defined in clause 4 of TS 36.211
3.3 Abbreviations p. 9
For the purposes of the present document, the abbreviations given in TR 21.905 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905.
ACS
Adjacent Channel Selectivity
DRX
Discontinuous Reception
E-UTRAN
Evolved Universal Terrestrial Radio Access Network
E-SMLC
Enhanced Serving Mobile Location Center
EARFCN
E-UTRAN Absolute Radio Frequency Channel Number
eNodeB
evolved Node B
LMU
Location Measurement Unit
RTOA
Relative Time of Arrival
SRS
Sounding Reference Signal
UE
User Equipment
UL
Uplink
UTDOA
Uplink Time Difference Of Arrival
