tech-invite   World Map     

3GPP     Specs     Glossaries     Architecture     IMS     UICC       IETF     RFCs     Groups     SIP     ABNFs       Search

Top          in Index          Prev          Next

TS 25.142 (RAN4)
UTRA – Base Station conformance testing (TDD)

|   ToC   |   3GPP‑Page   |   ETSI‑search   |   Help   |

(P) V14.0.0    2017/03    282 p.
(P) V13.1.0    2016/06    275 p.
(P) V12.2.0    2016/01    275 p.
(P) V11.5.0    2016/01    275 p.
(P) V10.5.0    2012/09    269 p.
(P) V9.6.0    2012/09    264 p.
(P) V8.9.0    2012/09    259 p.
(P) V7.14.0    2010/04    250 p.
(P) V6.10.0    2009/06    179 p.
(P) V5.12.0    2009/06    172 p.
(P) V4.13.0    2009/03    148 p.
(P) V3.15.0    2007/06    100 p.

Rapporteur:  Dr. Meyer, Juergen
See also:  TS 36.141     TS 37.141    

This TS specifies the Radio Frequency (RF) test methods and conformance requirements for UTRA Base Stations (BS) operating in the TDD mode. These have been derived from, and are consistent with, the UTRA base station (BS) specifications defined in TS 25.105. This TS covers all three options of the TDD mode, which are the 3,84 Mcps, the 1,28 Mcps and the 7.68 Mcps options respectively. The requirements are listed in different subsections only if the parameters deviate.

In this TS, the reference point for RF connections (except for the measurement of mean transmitted RF carrier power) is the antenna connector, as defined by the manufacturer. This TS does not apply to repeaters or RF devices which may be connected to an antenna connector of a BS.


Here          Top          None          None          Next
part:    1     2     3     4     5     6     7



1   Scope [R3]   PDF-p. 18
2   References [R3]
3   Definitions, symbols, and abbreviations [R3]   PDF-p. 19
4   Frequency bands and channel arrangement [R3]   PDF-p. 22
5   General test conditions and declarations [R3]   PDF-p. 24
5.1   Base station classes
5.2   Output power   PDF-p. 25
5.3   Specified frequency range and supported channel bandwidth
5.4   Relationship between RF generation and chip clock
5.5   Spectrum emission mask
5.6   Adjacent Channel Leakage power Ratio (ACLR)      Up
5.7   Tx spurious emissions   PDF-p. 27
5.8   Blocking characteristics
5.9   Test environments
5.10   Acceptable uncertainty of Test System   PDF-p. 30
5.11   Test Tolerances (informative)
5.12   Interpretation of measurement results
5.13   Selection of configurations for testing   PDF-p. 42
5.14   BS Configurations
5.15   Overview of the conformance test requirements
5.16   Format and interpretation of tests   PDF-p. 46
5.17   Regional requirements
5.18   Definition of Additive White Gaussian Noise (AWGN) Interferer   PDF-p. 47
5.19   Applicability of requirements [R9]
5.20   Test configurations for multi-carrier operation [R11]   PDF-p. 48
5.21   Applicability of test configurations [R11]
5.22   Requirements for BS capable of multi-band operation [R11]   PDF-p. 51

Up          Top          ToC