tech-invite   World Map     

IETF     RFCs     Groups     SIP     ABNFs    |    3GPP     Specs     Glossaries     Architecture     IMS     UICC    |    search

Top          in Index          None          Next

TS 36.101 (RAN4)
E-UTRA – User Equipment radio transmission and reception

|   ToC   |   3GPP‑Page   |   ETSI‑search   |   Help   |

(W-zip) V14.1    2016/09    1187 p.
(P) V13.5    2016/09    1129 p.
(P) V12.13    2016/09    773 p.
(P) V11.18    2016/09    503 p.
(P) V10.23    2016/09    357 p.
(P) V9.24    2016/03    215 p.
(P) V8.27    2016/03    171 p.


Rapporteur:  Mr. Fernandes, Edgar
See also:  TS 25.101 (UTRA FDD)     TS 25.102 (UTRA TDD)    


This TS establishes the minimum RF characteristics and minimum performance requirements for E-UTRA User Equipment (UE).



 

Here          Top          None          None          Next

 

1 Scope    2 References    3 Definitions, symbols and abbreviations    4 General    5 Operating bands and channel arrangement    6 Transmitter characteristics    6.1 General    6.2 Transmit power    6.3 Output power dynamics    6.4 Void    6.5 Transmit signal quality    6.6 Output RF spectrum emissions    6.6A Void    6.6B Void    6.7 Transmit intermodulation    6.8 Void    6.8A Void    6.8B Time alignment error for UL-MIMO    7 Receiver characteristics    7.1 General    7.2 Diversity characteristics    7.3 Reference sensitivity power level    7.4 Maximum input level    7.4A Void    7.5 Adjacent Channel Selectivity (ACS)    7.6 Blocking characteristics    7.6A Void    7.6B Blocking characteristics for UL-MIMO    7.7 Spurious response    7.8 Intermodulation characteristics    7.9 Spurious emissions    7.10 Receiver image    8 Performance requirement    9 Reporting of Channel State Information    10 Performance requirement (MBMS)    11 Performance requirement (ProSe Direct Discovery)    12 Performance requirement (ProSe Direct Communication)    A Measurement channels    B Propagation conditions    C Downlink Physical Channels    D Characteristics of the interfering signal    E Environmental conditions    F Transmit modulation    G Reference sensitivity level in lower SNR    H Modified MPR behavior    I Change history   

 

1   Scope [R8]   PDF-p. 26
2   References [R8]
3   Definitions, symbols and abbreviations [R8]
4   General [R8]   PDF-p. 32
5   Operating bands and channel arrangement [R8]
5.1   General
5.2   Void
5.3   Void
5.4   Void
5.5   Operating bands
5.5A   Operating bands for CA [R10]   PDF-p. 36
5.5B   Operating bands for UL-MIMO [R10]   PDF-p. 46
5.5C   Operating bands for Dual Connectivity [R12]
5.5D   Operating bands for ProSe [R12]   PDF-p. 48
5.5E   Operating bands for UE category 0 and UE category M1 [R12]   PDF-p. 49
5.5F   Operating bands for category NB1 [R13]
5.6   Channel bandwidth      Up
5.6A   Channel bandwidth for CA [R10]   PDF-p. 52
5.6B   Channel bandwidth for UL-MIMO [R10]   PDF-p. 73
5.6C   Channel bandwidth for Dual Connectivity [R12]
5.6D   Channel bandwidth for ProSe [R12]
5.6F   Channel bandwidth for category NB1 [R13]   PDF-p. 74
5.7   Channel arrangement   PDF-p. 75
6   Transmitter characteristics [R8]
6.1   General
6.2   Transmit power   PDF-p. 80
6.2.1   Void
6.2.2   UE maximum output power
6.2.2A   UE maximum output power for CA [R10]   PDF-p. 82
6.2.2B   UE maximum output power for UL-MIMO [R10]   PDF-p. 83
6.2.2C   Void
6.2.2D   UE maximum output power for ProSe [R13]   PDF-p. 85
6.2.2E   UE maximum output power for Category M1 UE [R13]
6.2.2F   UE maximum output power for category NB1 [R13]   PDF-p. 86
6.2.3   UE maximum output power for modulation / channel bandwidth      Up
6.2.3A   UE Maximum Output power for modulation / channel bandwidth for CA [R10]   PDF-p. 87
6.2.3B   UE maximum output power for modulation / channel bandwidth for UL-MIMO [R10]   PDF-p. 89
6.2.3D   UE maximum output power for modulation / channel bandwidth for ProSe [R12]
6.2.3E   UE maximum output power for modulation / channel bandwidth for category M1 [R13]
6.2.3F   UE maximum output power for modulation / channel bandwidth for category NB1 [R13]   PDF-p. 90
6.2.4   UE maximum output power with additional requirements
6.2.4A   UE maximum output power with additional requirements for CA [R10]   PDF-p. 100
6.2.4B   UE maximum output power with additional requirements for UL-MIMO [R10]
6.2.4D   UE maximum output power with additional requirements for ProSe [R12]   PDF-p. 107
6.2.4E   UE maximum output power with additional requirements for category M1 UE [R13]
6.2.5   Configured transmitted power   PDF-p. 108
6.2.5A   Configured transmitted power for CA [R10]   PDF-p. 122      Up
6.2.5B   Configured transmitted power for UL-MIMO [R10]   PDF-p. 124
6.2.5C   Configured transmitted power for Dual Connectivity [R12]   PDF-p. 125
6.2.5D   Configured transmitted power for ProSe [R12]   PDF-p. 126
6.2.5F   Configured transmitted Power for category NB1 [R13]   PDF-p. 128
6.3   Output power dynamics   PDF-p. 129
6.3.1   Void
6.3.2   Minimum output power
6.3.2A   UE Minimum output power for CA [R10]
6.3.2B   UE Minimum output power for UL-MIMO [R10]      Up
6.3.2C   Void
6.3.2D   UE Minimum output power for ProSe [R13]
6.3.2F   UE Minimum output power for category NB1 [R13]
6.3.3   Transmit OFF power
6.3.3A   UE Transmit OFF power for CA [R10]   PDF-p. 131
6.3.3B   UE Transmit OFF power for UL-MIMO [R10]
6.3.3D   Transmit OFF power for ProSe [R12]   PDF-p. 132      Up
6.3.3F   Transmit OFF power for category NB1 [R13]
6.3.4   ON/OFF time mask
6.3.4A   ON/OFF time mask for CA [R10]   PDF-p. 136
6.3.4B   ON/OFF time mask for UL-MIMO [R10]      Up
6.3.4D   ON/OFF time mask for ProSe [R12]
6.3.4F   ON/OFF time mask for category NB1 [R13]
6.3.5   Power Control
6.3.5A   Power control for CA [R10]   PDF-p. 142
6.3.5B   Power control for UL-MIMO [R10]
6.3.5D   Power Control for ProSe [R12]
6.3.5E   Power control for category M1 [R13]   PDF-p. 144
6.3.5F   Power Control for category NB1 [R13]
6.4   Void
6.5   Transmit signal quality      Up
6.5.1   Frequency error
6.5.1A   Frequency error for CA [R10]   PDF-p. 145
6.5.1B   Frequency error for UL-MIMO [R10]
6.5.1D   Frequency error for ProSe [R12]
6.5.1F   Frequency error for UE category NB1 [R13]
6.5.2   Transmit modulation quality
6.5.2A   Transmit modulation quality for CA [R10]   PDF-p. 149
6.5.2B   Transmit modulation quality for UL-MIMO [R10]   PDF-p. 152
6.5.2D   Transmit modulation quality for ProSe [R12]
6.5.2E   Transmit modulation quality for category M1 [R13]
6.5.2F   Transmit modulation quality for Category NB1 [R13]   PDF-p. 155
6.6   Output RF spectrum emissions   PDF-p. 156
6.6.1   Occupied bandwidth   PDF-p. 157
6.6.1A   Occupied bandwidth for CA [R10]
6.6.1B   Occupied bandwidth for UL-MIMO [R10]
6.6.1F   Occupied bandwidth for category NB1 [R13]   PDF-p. 158
6.6.2   Out of band emission
6.6.2A   Void
6.6.2B   Out of band emission for UL-MIMO [R10]   PDF-p. 166
6.6.2C   Void
6.6.2D   Out of band emission for ProSe [R13]
6.6.2F   Out of band emission for category NB1 [R13]   PDF-p. 167
6.6.3   Spurious emissions   PDF-p. 168
6.6.3.1   Minimum requirements
6.6.3.1A   Minimum requirements for CA [R10]   PDF-p. 169
6.6.3.2   Spurious emission band UE co-existence   PDF-p. 170
6.6.3.2A   Spurious emission band UE co-existence for CA [R10]   PDF-p. 176      Up
6.6.3.3   Additional spurious emissions   PDF-p. 183
6.6.3.3.1   Minimum requirement (network signalled value "NS_05")
6.6.3.3.2   Minimum requirement (network signalled value "NS_07")
6.6.3.3.3   Minimum requirement (network signalled value "NS_08") [R9]   PDF-p. 184
6.6.3.3.4   Minimum requirement (network signalled value "NS_09") [R9]
6.6.3.3.5   Minimum requirement (network signalled value "NS_12") [R11]
6.6.3.3.6   Minimum requirement (network signalled value "NS_13") [R11]   PDF-p. 185
6.6.3.3.7   Minimum requirement (network signalled value "NS_14") [R11]
6.6.3.3.8   Minimum requirement (network signalled value "NS_15") [R11]
6.6.3.3.9   Minimum requirement (network signalled value "NS_16") [R11]      Up
6.6.3.3.10   Minimum requirement (network signalled value "NS_17") [R11]   PDF-p. 186
6.6.3.3.11   Minimum requirement (network signalled value "NS_18") [R11]
6.6.3.3.12   Minimum requirement (network signalled value "NS_19") [R11]
6.6.3.3.13   Minimum requirement (network signalled value "NS_11") [R10]
6.6.3.3.14   Minimum requirement (network signalled value "NS_20") [R10]   PDF-p. 187
6.6.3.3.15   Minimum requirement (network signalled value "NS_21") [R10]
6.6.3.3.16   Minimum requirement (network signalled value "NS_22") [R10]
6.6.3.3.17   Minimum requirement (network signalled value "NS_23") [R12]   PDF-p. 188
6.6.3.3.18   Void
6.6.3.3.19   Minimum requirement (network signalled value "NS_04") [R12]
6.6.3.3.20   Minimum requirement (network signalled value "NS_24") [R13]   PDF-p. 189      Up
6.6.3.3.21   Minimum requirement (network signalled value "NS_25") [R13]
6.6.3.3.22   Minimum requirement (network signalled value "NS_26") [R13]
6.6.3.3A   Additional spurious emissions for CA [R10]   PDF-p. 190
6.6.3A   Void
6.6.3B   Spurious emission for UL-MIMO [R10]
6.6.3C   Void
6.6.3D   Spurious emission for ProSe [R13]
6.6.3F   Spurious emission for category NB1 [R13]
6.6A   Void
6.6B   Void
6.7   Transmit intermodulation   PDF-p. 193
6.8   Void
6.8A   Void
6.8B   Time alignment error for UL-MIMO [R10]   PDF-p. 195
7   Receiver characteristics [R8]
7.1   General
7.2   Diversity characteristics   PDF-p. 196
7.3   Reference sensitivity power level
7.4   Maximum input level   PDF-p. 252
7.4A   Void
7.5   Adjacent Channel Selectivity (ACS)
7.6   Blocking characteristics   PDF-p. 260
7.6A   Void
7.6B   Blocking characteristics for UL-MIMO [R10]      Up
7.7   Spurious response   PDF-p. 275
7.8   Intermodulation characteristics
7.9   Spurious emissions
7.10   Receiver image [R10]

Up          Top          ToC